Рели

• Voltage being detected in one of two ranges: 85...250 VAC or 170...250 VAC (settable by jumper)
• Galvanic isolation between the input voltage and output (OC)
• Low temperature drift
• Supplied by detected voltage
• Warranty: 3 years

• The Si-83 tank pump is perfect for residential A/C (up to 20 kW) and heating units (up to 40 kW)
• Max discharge head: 5,4 m
• Max pressure: 5,7 m
• Tank volume: 2 L
• Automatic turn on specific level in tank
• Overdraft level safety switch
• Stainless steel motor shaft
• Protection class: IP44
• Max condensate temperature: 55 °C
• Max condensate acidity: pH > 2,5 (Gas condensing boilers)
• Quick installation with mobile app

Astronomical digital clocks RAT-TPA1B are applied for switching on and off the lightning or other electrical receivers in accordance to sunset and sunrise with an option to program a night break, which means a temporary switching off of the receivers for savings purposes

• 52 programs, holiday mode
• Automatic summer/winter digital clockover
• Automatic transfer of weekdays
• Sealable cover of the front panel, easy setting by 4 buttons
• Backlighted LCD display (can be turned off)
• 10-year power reserve (internal lithium battery which can protect real time clock and all the settings when the electric power supply is off)
• Number and type of contacts: 1 CO
• Rated load: 16 A / 250 V AC
• Direct mounting on 35 mm rail mount acc. to EN 60715
• Compliance with standards EN 60730-1, EN 60730-2-7, Directive RoHS

• Module is designed to protect battery if it discharges below 10,5 V mark, disconnecting it from load
• Battery is automatically reconnected to load if its voltage rises
• Suitable for work with heaters, lighting, travel refrigerators, etc.
• Operating voltage: 12 V ZBxx, 24 V ZBxx-24V, 48 V ZB-48V
• Maximal current: 40 A ZB40, 80 A ZB80, 140 A ZB140
• Operating temperature: -20...50 °C
• Dimensions: 65 x 89 x 70 mm

• SET-1000 + SET/OSK2 is designed for oil detection on water surface
• Can be used in tanks where water level is alternating
• Control device SET-1000 is a one-channel level switch
• SET/OSK2 sensor detects more than 15 mm width hydrocarbon layer on water surface
• Polypropylene floats
• ATEX certified
• Wall-mounted, IP67
• Supply: 230 VAC, 50/60 Hz

• The versatile Si 2052 is suitable for replacement of some market standards drain pumps used in cassette type air-conditioning units up to 20 kW
• Max discharge head: 0,9 m (flow rate = 24 l/h)
• The single level detection unit can be used as a safety contact (NC 50 VA resistive – 250 V) to cut off automatically the air conditioning system compressor or solenoid valve
• The centrifugal technology inside this pump is specifically designed for removing condensates continuously, in any kind of environment, with a very low sound level (≤ 30 dBA)
• Protection class: IPX4
• Operating conditions: 100 % - continuous duty

• Lokaset 20 is designed for high wastewater level detection in septic tanks
• Easy to install, does not need calibration
• Switch output
• Visual and acoustic alarms
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

The DPI series electronic pressure measuring devices are engineered for building automation in HVAC/R industry. The most technologically advanced and versatile electronic differential pressure switches on the market, combining up to two relay outputs and 0–10 V output options.

Differential manometer DPG/PS for air and non-aggressive gasses, designed for pressure monitoring and control. Used in ventilation and conditioning systems for filter permeability control.

• Range: 0…1500 Pa
• Switch activation range: 20…1500 Pa
• Operating temperature: -5… +60°C

Differential manometer MM/PS for air and non-aggressive gasses, designed for pressure monitoring and control. Used in ventilation and conditioning systems for filter permeability control.

• Range: 0…1500 Pa
• Switch activation range: 40…1500 Pa
• Operating temperature: -20… +60°C

• Pressure range: from -1...6 to -1...18 bar
• Output signal: 1 Floating change-over contact (SPDT)
• Process temperature: -40...+150 °C
• Process connection: G1/4" f, G1/8" f, G1/2" m
• Protection class: IP65

Differential pressure switch is designed for use in air and non-aggressive gasses. Made by HK Instruments (Finland).

Vertical, stainless steel, float level sensor with float protection against mechanical impact, designed for level control.

• Material of float: stainless steel AISI 316 SS
• Max. temperature: -30...+105 °C
• Switch rating: 50 VA
• Switching voltage: 230 AC / DC

The FPI 8237 IO-Link Flush Membrane pressure transmitter impresses with an absolutely smooth and robust flush-mounted measuring diaphragm made of corrosion-resistant duplex steel 1.4462. Trafag’s proprietary thin-film-on-steel sensor technology ensures a wide temperature range and excellent long-term stability.

• Measuring range: -0,5...0,5 to 0...100 bar
• Output signal: IO-Link 1.1, COM3, min. process cycle time 1 ms, Smart Sensor Profile ED2, 2 Switching outputs PNP / NPN / Push-Pull configurable
• Accuracy at 25°C typically: ± 0.5 % FS typ.
• Measuring principle: Thin-film-on-steel
• Media temperature –10... +125 °C
• Ambient temperature: –10...+125 °C
• Protection class: IP65, IP67
• Applications: Hydraulics, Machine tools, Process technology, Food industry, Water treatment

• GA-1 is designed for grease detection in separators, basins and tanks
• Easy to install, does not need calibration
• Switch output
• Remote monitoring capability
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• GA-2 is designed for grease detection in separators, basins and tanks
• Two sensors – one is for grease detection, other – for blockage control
• Easy to install, does not need calibration
• 2 switch outputs
• Remote monitoring capability
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

High frequency limit level sensors with elimination of deposits and foam on the electrode for vertical mounting

• High frequency limit level sensors with elimination of deposits and foam on the electrode for vertical mounting,
• Resistant to adhesion of viscous and sticky media (ketchup, yoghurt, spreads, syrups, creams, pastes, cleaning agents, alkalis, etc.)
• Unique material type resolution function "Medium window" (the sensor is sensitive only to the set medium and does not react to substances with lower and higher permittivity)
• Can replace vibration level sensors
• Universal design for all types of liquids (electrically conductive or non-conductive)
• For vertical mounting
• Adjustment with a magnetic pen before installation

• High level detection
• Oil on water surface detection
• Designed for usage in separators, basins and tanks
• Easy to install, does not need calibration
• Reliable long-term se in harshest conditions
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• Temperature measurement range:
  a) Ambient model: -20...+80 °C
  b) Remote model with polycarbonate probe: -20...+80 °C
  c) Remote model with stainless steel probe: -40...180 °C
• Relative humidity measurement range: 0...100 %
• Calculates dew point, absolute humidity, enthalpy and combination ratio
• 4-wire analog output: 0...5/10 V or 0/4...20 mA
• 2 relay outputs
• Versions with or without display
• Protection class: IP65 (ABS V0 housing)

• Pressure range: from 0...2,5 to 0...600 bar
• Output signal: 1 or 2 PNP transistors
• Process temperature: -40...+125 °C
• Process connection: G1/4" m, G1/4" m (Manometer), 1/4"NPT m, 1/8"NPT m, 7/16"-20UNF SAE J512 f, 7/16"-20UNF SAE4 m, 7/16"-20UNF m DIN3866, R1/4" m DIN3858, R1/4" m DIN2999, R1/8" m, M10x1 m, M12x1.5 m
• Protection class: IP65, IP67

HST comes in three models, HST-M – standard model (IP20), HST-D – remote sensor (IP65) and HST-A – channel model (IP65).

“idOil®” is an alarm system intended for monitoring liquid levels particularly in oil and sand separators. The system consists of the idOil control unit and the idOil sensors installed in the separator. The sensor cables can be extended with a cable connector or connection box. One to three digital idOil sensors of the same or different type can be connected to the control unit. The sensors can be used to monitor the following:

• High liquid level (idOil-LIQ high liquid level sensor)
• Oil layer detection (idOil-OIL oil sensor is for class IIA explosive liquids and idOil-OIL-Soil sensor is for class IIB explosive liquids)
• Sludge layer detection (idOil-SLU sludge sensor)

“idOil®” is an alarm system intended for monitoring liquid levels particularly in oil and sand separators. The system consists of the idOil control unit and the idOil sensors installed in the separator. The sensor cables can be extended with a cable connector or connection box. One to three digital idOil sensors of the same or different type can be connected to the control unit. The sensors can be used to monitor the following:

• High liquid level (idOil-LIQ high liquid level sensor)
• Oil layer detection (idOil-OIL oil sensor is for class IIA explosive liquids and idOil-OIL-Soil sensor is for class IIB explosive liquids)
• Sludge layer detection (idOil-SLU sludge sensor)

• Three versions by sensitivity: NS (standard), AS (high), SR (adjustable)
• Operating resistance: 5,6 kΩ (NS) 70 kΩ (AS) 0...100 kΩ (SR)
• Mounting on DIN rail
• Operating temperature: -10...50 °C
• Supply: 117/230/400 VAC
• Protection class: IP20

• Input: standard 4...20 mA signal or capacitive Labkotec 3W probe
• Current output: 0/4...20 mA
• Switch outputs: 2 units
• LCD display
• Programmable using buttons
• ATEX certified
• Wall-mounted, IP65
• Supply: 230 VAC, 50/60 Hz

• High level detection
• Oil on water surface detection
• Sludge under water detection
• Designed for usage in separators, basins and tanks
• Version with GSM module available – for alarms and service reminders
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• For liquids limit level sensing on non-conductive (glass or plastic) gauge-pipes, tubes and tank walls
• Output: switch or PNP
• Sensitivity setting by means of magnetic pen
• LED indication
• Prismatic or planar electrode
• Versions with a fixed cable or a connector
• Supply: 6...30 VDC
• Operating temperature: -20...+80 °C
• Protection class: IP67

• Output: switch
• Application: level sensing for solids
• Supply: 24 VDC / 220 VAC
• Sensitivity setting: 3 positions
• Rotation speed: 1 per minute
• Operating temperature: -20...+70 °C
• Operating pressure: up to 0,8 bar
• Material: body – plastic, other component – stainless steel
• Protection class: IP65
• Weight: 1 kg

The enLink Status-VC transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• 0…20 mA, 0…10 V or resistance input
• 12 bit resolution
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Case IP40 protection (IP 67 on request)

The enLink Status-P transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• 3 channels pulse counter (S0 standard) and monitor of state (open / closed)
• With the transmit on Change of State enabled the unit operates as a standard pulse counter and also transmits a message when the state of the input changes from closed to open or open to closed
• The pulse counts for each channel are written to memory every 5 – 10 minutes
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours or adaptive (triggered by change of state)
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Case IP40 protection (IP 67 on request)

• Wide gap between the two parts of sensor
• Protection class: IP65
• Max switching voltage: 100 V
• Max switching current: 0,5 A
• Cable length: 0,45 m
• Warranty: 3 years

Multifunction astronomical digital clocks RDT-TPA2 are applied for switching on and off the lightning or other electrical receivers in accordance to sunset and sunrise.

• 80 programs (astronomical and annual), holiday mode, random mode
• Automatic summer/winter digital clockover
• Automatic transfer of weekdays
• Sealable cover of the front panel, easy setting by 4 buttons
• Backlighted LCD display (can be turned off)
• 10-year power reserve (internal lithium battery which can protect real time clock and all the settings when the electric power supply is off)
• Number and type of contacts: 2 CO (each channel can be assigned an individual program)
• Rated load: 16 A / 250 V AC
• Direct mounting on 35 mm rail mount acc. to EN 60715
• Compliance with standards EN 60730-1, EN 60730-2-7, Directive RoHS

• 10 time functions. With control signal and without additional signal
• 10 time ranges. Ranging from 0,1 sec. to 30 hours
• Operating voltage: 12…240 V AC / DC
• Operating power: < 4 VA
• Mounting on DIN rail
• Operating temperature: -20…+55 °C

The AUREGIS LJ-VD4M12 multi-zone floating, stainless steel level relay with standard M12 connector is designed for liquid level measurement and regulation.

• Connection connector: M12 (4 / 8 pins)
• Floats and float holders are customizable (on request)
• Connection thread: G3/4" or larger (on request)
• Switching power: 25 VA
• Switching voltage: 24 V AC/DC
• Process part operating temperature: -30...+105 °C
• Process part: Stainless steel AISI316L
• Protection class: IP65

• OilSET-1000 is designed for oil detection in separators, basins and tanks
• Easy to install, does not need calibration
• 2 switch outputs
• Ultrasonic sensor SET/S, 5 meter cable
• ATEX certified
• Wall-mounted, IP67
• Supply: 230 VAC, 50/60 Hz

Applications:

Surge protection for 2 pair lines or 4 single lines with common reference potential in the data, signal and communication systems: 0-20 mA, 4-20 mA current loop, TTY 4-20 mA, TTY, TTL, V24 (RS232C), high-frequency transmission system.

Specifications:

• ANSI / IEEE C62.41 category: B, C
• Rated operating voltage Un 24 V DC
• Max. continuous operating voltage Uc 33 V DC / 23,3 V AC
• Rated load current at 25°C IL 1 A
• Nom. discharge current (8/20 μs) In 10 kA
• Max. discharge current (8/20 μs) Imax 20 kA
• D1 current impulse (10/350 μs, per line) 2,5 kA
• Voltage protection level Up:
  • at In, C2 (8/20 μs, line-line, line-PG) ≤ 55 V
  • at C3, 1 kV/µs (line-line, line-PG) ≤ 48 V
• Compliance with standards: EN 61643-11:2012, EN 61643-21:2001+A1:2009+A2:2013, EN 61643-31:2019

Applications:

surge protection for 2 pair lines of closed circuit (loops) in the data, signal and communication systems: 4-20 mA current loop, analog/digital communication, RS485, RS422 (V11) interface, high-frequency bus system, 2 wires video transmission system.

Specifications:

• ANSI / IEEE C62.41 category: B, C
• Rated operating voltage Un 24 V DC
• Max. continuous operating voltage Uc 33 V DC / 23,3 V AC
• Rated load current at 25°C IL 1 A
• Nom. discharge current (8/20 μs) In 10 kA
• Max. discharge current (8/20 μs) Imax 20 kA
• D1 current impulse (10/350 μs, per line) 2,5 kA
• Voltage protection level Up:
  • at In, C2 (8/20 μs, line-line) ≤ 55 V
  • at In, C2 (8/20 μs, line-PG) ≤ 500 V
  • at C3, 1 kV/µs (line-line) ≤ 48 V
  • at C3, 1 kV/µs (line-PG) ≤ 600 V
• Compliance with standards: EN 61643-11:2012, EN 61643-21:2001+A1:2009+A2:2013, EN 61643-31:2019

Applications:

• For protecting low voltage equipment against lightning and surge damages
• For installation in conformity with the lightning protection zones concept at LPZ 0-1
• Designed according to IEC 61643-11:2011

Specifications:

• Category IEC / EN / VDE: class II+III / type 2+3 / C+D
• Max. continuous operating voltage Uc 275 V AC
• Nom. discharge current (8/20 μs) In 10 kA
• Max. discharge current (8/20 μs) Imax 20 kA
• Voltage protection level Up ≤ 1,5 kV
• Max. backup fuse 125 A

• PID control function with accurate self-tuning
• Input: Pt100 (-200…+600 °C ± 0,5 % of full scale ± 1 digit)
• Relay output: 250 V AC (5, 8, 16 A) NO / NC
• Control algorithm: On-Off / P, PI, PD, PID (configurable)
• Soft start feature
• Selectable heating / cooling control
• In case of sensor failure, periodically, auto-periodically running or relay state can be selected
• Mountable on DIN rail
• Power supply: 230 V AC, 10…30 V DC - 8…24 V AC (selectable on order)
• Operating temperature: 0…+50 °C

• Pressure range: from -0,9...1,5 to 4...40 bar
• Output signal: 1 Floating change-over contact (SPDT)
• Process temperature: -40...+150 °C
• Process connection: G1/4" f, G1/2" m
• Protection class: IP66

• Pressure range: from 1...10 to 60...600 bar
• Output signal: 1 Floating change-over contact (SPDT)
• Process temperature: -30...+100 °C / -15...+150 °C
• Process connection: G1/4" f, G1/2" m
• Protection class: IP66

• Pressure range: from 0...2,5 to 0...600 bar
• Output signal: 1 or 2 PNP transistors
• Process temperature: -40...+125 °C
• Process connection: G1/4" m, G1/4" m (Manometer), 1/4"NPT m, 1/8"NPT m, 7/16"-20UNF SAE J512 f, 7/16"-20UNF SAE4 m, 7/16"-20UNF m DIN3866, R1/4" m DIN3858, R1/4" m DIN2999, R1/8" m, M10x1 m, M12x1.5 m
• Protection class: IP65, IP67

The small sensor dimension combined with IO-Link, the pressure and temperature value of the media make the NAI 8273 the ideal choice in various applications.

• Measuring range: -0.2...0.2 to 0...700 bar
• Output signal: IO-Link 1.1, COM3, min. process cycle time 1 ms, Smart Sensor Profile ED2, 2 Switching outputs PNP / NPN
• Accuracy at 25°C typically: ± 0.3 % FS typ., ± 0.5 % FS typ.
• Measuring principle: Thin-film-on-steel
• Media temperature –40... +125 °C
• Ambient temperature: –40...+125 °C
• Protection class: IP65, IP67
• Applications: Hydraulics, Machine tools, Process technology

• Pressure range: from 0...6 to 0...600 bar
• Output signal: 4...20 mA / 1 x PNP / 2 x PNP
• Process temperature: -40...+125 °C
• Accuracy: 0,3 %
• Dielectric strength: 710 V
• Measurement principle: thin film on steel
• Protection class: IP65, IP67
• Conformity: EN 50155, EN 45545-2, EN 61373, EN 50121-3-2
• Parametrization by SMI programmer (not included) via Bluetooth connection from smartphone (Android)

• Various pressure measurement ranges: 0,1...1000 bar
• Relay output: 2 units
• Output: 0...20 mA / 4...20 mA
• Process temperature: -40...150 °C
• Operating temperature: -25...85 °C
• Materials: stainless steel, titanium

• Output relay: SPDT / 3A / 250VAC
• Application: level sensing for solids and powder
• Speed: 1 RPM
• Supply: 24 VDC or 220 VAC
• Operating temperature: - 10...+ 70 °C
• Operating pressure: - 0,6...+ 0,6 bar
• Protection class: IP66

They are used to regulate the power delivered to the receiver, where this power is proportional to the input control signal. They are used in automation control systems where smooth control of receiver power is required for resistive or resistive-inductive loads. Typical applications for power controllers: heaters, industrial furnaces (annealing, quenching, drying, etc.), dryers, plastics processing equipment, industrial sealing machines, glass production industry, industrial heating systems (matting and lining of pipelines), load transformers.

• Single-phase power controller (phase angle load control)
• Control input: DC voltage 0...10 V DC (RSR92-..V..) or current 4...20 mA (RSR92-..I..)
• SCR output (thyristors)
• Load current 25...80 A
• Max. load voltage 280, 530 V AC (single-phase)
• Dielectric strength 4 000 Vrms (opto-isolation)
• MOV protection (built-in varistor)
• Mounting on panel or on heatsinks
• Recognitions, certifications, directives: RoHS, REACH, CE, EAC

• Sludge and sand detection
• Oil on water surface detection
• Designed for usage in separators, basins and tanks
• Easy to install, does not need calibration
• Reliable long-term se in harshest conditions
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz