Регуляторы уровня

• SET-1000 + SET/OSK2 is designed for oil detection on water surface
• Can be used in tanks where water level is alternating
• Control device SET-1000 is a one-channel level switch
• SET/OSK2 sensor detects more than 15 mm width hydrocarbon layer on water surface
• Polypropylene floats
• ATEX certified
• Wall-mounted, IP67
• Supply: 230 VAC, 50/60 Hz

• Lokaset 20 is designed for high wastewater level detection in septic tanks
• Easy to install, does not need calibration
• Switch output
• Visual and acoustic alarms
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• GA-1 is designed for grease detection in separators, basins and tanks
• Easy to install, does not need calibration
• Switch output
• Remote monitoring capability
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• GA-2 is designed for grease detection in separators, basins and tanks
• Two sensors – one is for grease detection, other – for blockage control
• Easy to install, does not need calibration
• 2 switch outputs
• Remote monitoring capability
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• High level detection
• Oil on water surface detection
• Designed for usage in separators, basins and tanks
• Easy to install, does not need calibration
• Reliable long-term se in harshest conditions
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• Adjustable start time delay: 0...16 s
• Operating resistance: 0...100 kΩ
• Mounting on DIN rail
• Operating temperature: -10...50 °C
• Supply: 117/230/400 VAC
• Protection class: IP20

• Three versions by sensitivity: NS (standard), AS (high), SR (adjustable)
• Operating resistance: 5,6 kΩ (NS) 70 kΩ (AS) 0...100 kΩ (SR)
• Mounting on DIN rail
• Operating temperature: -10...50 °C
• Supply: 117/230/400 VAC
• Protection class: IP20

• Input: standard 4...20 mA signal or capacitive Labkotec 3W probe
• Current output: 0/4...20 mA
• Switch outputs: 2 units
• LCD display
• Programmable using buttons
• ATEX certified
• Wall-mounted, IP65
• Supply: 230 VAC, 50/60 Hz

• High level detection
• Oil on water surface detection
• Sludge under water detection
• Designed for usage in separators, basins and tanks
• Version with GSM module available – for alarms and service reminders
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• OilSET-1000 is designed for oil detection in separators, basins and tanks
• Easy to install, does not need calibration
• 2 switch outputs
• Ultrasonic sensor SET/S, 5 meter cable
• ATEX certified
• Wall-mounted, IP67
• Supply: 230 VAC, 50/60 Hz

• Sludge and sand detection
• Oil on water surface detection
• Designed for usage in separators, basins and tanks
• Easy to install, does not need calibration
• Reliable long-term se in harshest conditions
• Acoustic and visual alarms
• 2 switch outputs
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz

• SandSet-1000 is designed for sludge and sand detection in separators, basins and tanks
• Easy to install, does not need calibration
• Reliable long-term se in harshest conditions
• Acoustic and visual alarms
• 2 switch outputs or output to LabkoNet remote monitoring system
• Ultrasonic sensor SET/S, 5 meter cable
• ATEX certified
• Wall-mounted, IP67
• Supply: 230 VAC, 50/60 Hz

• Separator alarm system for applications where mains supply is not available
• ATEX certified
• Alarms:
  • high level detection
  • oil on water surface detection
  • sludge under water detection
• SolarSet Beacon consists of:
  • housing containing and panel
  • battery
  • charger controller
  • flashing beacon for alarm
  • sludge and oil level sensor system LevelSet S

• Separator alarm system for applications where mains supply is not available
• ATEX certified
• Alarms:

• high level detection

• oil on water surface detection

• sludge under water detection

• SolarSet Beacon consists of:

• housing containing and panel

• battery

• charger controller

• GSM/GPRS modem

• flashing beacon for alarm

• sludge and oil level sensor system LevelSet S

• Separator alarm system for applications where mains supply is not available
• ATEX certified
• Alarms:
  • high level detection
  • oil on water surface detection
  • sludge under water detection
• SolarSet Beacon consists of:
  • housing containing and panel
  • battery
  • charger controller
  • GSM/GPRS modem
  • sludge and oil level sensor system LevelSet S

• Up to 10 / 15 m level measurement with automatic temperature compensation
• Calculation of filling in the tank or flow in open channels
• Galvanically isolated 0/4...20 mA analog output
• Digital RS-485 Modbus RTU interface
• 2 alarm outputs
• Internal data and setup memory
• Two 32-points individual characteristics (for recalculation)
• LCD screen
• Housing protection grade: IP66
• Sensor protection grade: IP66 / IP 68
• Supply: 12...25...40 VDC
• Operating temperature: -20...23...55 °C

• Up to 10 / 15 m level measurement
• Analog output: 4…20 mA
• Digital output: RS-485 Modbus RTU
• Resolution: 3 mm
• Supply: 24 VDC / 300 mA
• Operating temperature: -20...60 °C
• Cable length: 1 m

• Designed for the remote monitoring of measurements in industrial, domestic and environmental maintenance applications
• Typical applications include oil separator alarms, tank surface level measurements, monitoring pumping stations and real estate, and surface and groundwater measurements
• The device sends alarms and measurement results as text messages either directly to GSM phone or to the LabkoNet server
• Settings can be easily modified with a GSM phone
• Analog inputs: 4 units 4...20 mA (passive or active)
• Digital inputs: 4 units
• Relay outputs: 2 units
• Communication: SMS, GPRS
• Operating temperature: -20...+50 °C
• Supply: 230 VAC / 12 VDC battery
• Protection class: IP65

Fluid level alarm Elcluwo 111S, designed for usage with conductometric probes for fluid level alarm and control.

Technical specifications

• One or more level control
• Switch output 2A, 250 VAC
• Probe supply from isolated ~12 V source
• Adjustable sensitivity
• Available modes – flooding, drainage, dry flow, overflooding
• Pump or valve control
• Designed for work with various probes: SKS 401, 201, 101, SW-01 and others
• Mounting on standard rail (35 mm)

Fluid level alarm Elcluwo 112S, designed for usage with conductometric probes for fluid level alarm and control, depth pump protection.

Technical specifications

• One or more level control
• Switch outputs: switching + NO 2 A / 250 VAC
• Probe supply from isolated ~12 V source
• Adjustable sensitivity
• Available modes – flooding, drainage, dry flow, overflooding
• Pump or valve control
• Designed for work with various probes: SKS 401, 201, 101, SW-01 and others
• Mounting on standard rail (35 mm)

• One or more level control
• Switch outputs: switching + 3 x NO 2 A / 250 VAC
• Probes: galvanically isolated, max. 2mA, 5V~ 100 Hz
• Adjustable sensitivity
• Available modes – flooding, drainage, dry flow, overflooding
• Pump or valve control
• Designed for work with various probes: SKS 401, 201, 101, SW-01 and others
• Mounting on standard rail (35 mm)
• Supply: 230 VAC / 24 VAC

• One or two level control
• Switch outputs – switching + 5 x NO, 2A / 250 VAC
• Probes: galvanically isolated, max. 2uA, 5V~ 100 Hz
• Adjustable sensitivity
• Available modes – filling, draining, dry flow, overflow, two/three pump control and others
• Valve or gate control
• Adapted for work with various probes – SKS 401, 201, 101, SW-01 and others
• Mounted on standard rail (35 mm)
• Supply: 230 VAC / 24 VAC

• System consists of alarm device SET-1000 and fixed level vibration sensor SET/V
• For usage separators, basins and tanks
• Alarm device SET-1000 is a single-channel level switch
• When used with SET/V, SET-1000 alarms when set high level in tank is exceeded
• ATEX certified
• Wall-mounted
• Supply: 230 VAC, 50/60 Hz