Измерение и контроль температуры

Multifunctional indoor climate sensor AERASGARD RFTM - LQ - PS - CO2 - Modbus with with LCD display.

• Temperature measuring range / deviation: 0…+50 °C / ± 0,2 °C at +25 °C
• Humidity measuring range / deviation: 0…100 % RH / ± 2 % RH (20…80 % RH), at 25 °C, otherwise ± 3 %
• CO2 Measuring range / accuracy: 0…5000 ppm / ± 30 ppm ± 3 % of measured value
• Particulate matter (PM) measuring range / accuracy: 0…50 μg/m³ 0…100 μg/m³ 0…300 μg/m³ 0…500 μg/m³
• Particulate matter (PM) accuracy ± 10 μg/m3 (± 10 % of measured value) at PM 2.5, ± 25 μg/m3 (± 25 % of measured value) at PM 10
• Air quality (VOC) measuring range: 0…100 %
• Data output:  galvanically separated RS-485 Modbus RTU interface
• Variants: with / without LCD display
• One sensor covers about 30 m² of room area
• Power supply: 24 V ac/dc (200 mA)
• Standards: CE, EN 61 326, EMC Directive 2014/ 30/ EU, 2014/ 35/ EU

• Calorimetric measuring principle
• Units freely selectable via keys at the display
• Display shows 2 values at the same time, twistable by 180 ° degree
• Integrated Modbus interface enables connection control systems, SCADA
• M-Bus (optional)
• Analog output 4...20 mA
• Pulse output (galvanic isolation)
• High measuring accuracy (ideal for leakage measurement)

SKU: 5905309602212

• Efento Gateway automatically transfers gathered data from Efento BLE (Bluetooth Low Energy) sensors to Efento Cloud or any other IoT platform over 4G LTE
• Gateway stores 500,000 measurements in its buffer memory in case the connection to Efento Cloud is lost, it will send the measurements right after connection is restored
• If Gateway used without Efento cloud it can store sensors data in its memory
• In local mode you can check the current and historical measurements (table/chart) and export the data in a form of CSV report
• Gateway communicates with sensors wirelessly over BLE. The maximum distance between Gateway and sensor is 100 m in the open space and 20 – 30 m in the buildings
• One gateway supports up to 128 Efento sensors
• Gateway can be integrated with any cloud platform or software that supports HTTP protocol (REST API)
• Setup takes under 5 minutes and can be completed using a smartphone with a free mobile app
• SIM card slot for LTE Cat 1 connection
• Power supply: 5 V, 1 A (USB-C)
• Backup battery: LI-Po, 1900 mAh (up to 12 hours backup power)
• Operating temperature: 0…+40 °C

SKU: 5906660327066

• Efento Gateway automatically transfers gathered data from Efento BLE (Bluetooth Low Energy) sensors to Efento Cloud or any other IoT platform
• Gateway stores 500,000 measurements in its buffer memory in case the connection to Efento Cloud is lost, it will send the measurements right after connection is restored
• If Gateway used without Efento cloud it can store sensors data in its memory
• In local mode you can check the current and historical measurements (table/chart) and export the data in a form of CSV report
• Gateway communicates with sensors wirelessly over BLE. The maximum distance between Gateway and sensor is 100 m in the open space and 20 – 30 m in the buildings
• One gateway supports up to 128 Efento sensors
• Gateway can be integrated with any cloud platform or software that supports HTTP protocol (REST API)
• Configuration of Efento Gateway using any internet browser over LAN
• Ethernet connection for data transfer
• Power supply: 5 V, 1 A (mini USB)
• Operating temperature: 0…+40 °C

• Temperature measurement range: -20...+60 °C
• Accuracy: ±0.4 °C
• Internal temperature sensor
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 1 s...24 h
• Internal sensor
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Local alarms via LED indication, on LCD screen and acoustically by built-in beeper
• Data can be transferred to PC via USB-C interface
• Calibration certificate of manufacturer included
• Ambient temperature: -20...+60 °C
• Supply: 5200 mAh LiIon battery
• Protection class: IP67
• Warranty: 3 years

• Measures temperature, humidity, calculates dew point
• Temperature measurement range: -20...+60 °C
• Humidity measurement range: 0...100 %
• Memory: up to 500,000 values in non-cyclic mode (350,000 in cyclic)
• Logging interval: 10 s...24 h
• Display and alarm refresh interval: 1 s...1 min
• Protection class: IP67
• Warranty: 3 years
• Calibration certificate of manufacturer is included (according to EN ISO/IEC 17025)
• Free analytical software COMET Vision

• Inputs: 4x external Pt1000 sensors
  • Measuring range: -200…+260 °C
  • Accuracy: ± 0.2 °C (± 0,2 %, when temperature is in range of +100...+260 °C)
  • Resolution: 0,1 °C
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: adjustable 1 s, 10 s, 1 min
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Messages can be sent on alarms and periodically
• Data can be transferred to PC via USB-C interface
• Calibration certificate included
• Ambient temperature: -20...+60 °C
• Supply: rechargeable Li-Ion battery A8200, 3.6V/5200mAh
• Protection class: IP20
• Warranty: 3 years

• Used with grain temperature sensor cables GWSL 1100, GWSL 2100 and spear sensors GWTL-R
• Cable length up to 200 m (including the temperature cables)
• Up to 32 values of temperatures are shown in cycle
• Weight: 240 g (with batteries)
• Case material: ABS
• Supply: 2 x AA (battery life circa 1 year)
• Operating temperature: -20...+40 °C

SM400-4-TH humidity and temperature sensor supports MODBUS RTU protocol over the RS-485 interface. Suitable for environmental quality monitoring offices, server room, data center and indoor air

• Changeable communication parameters
• Non-volatile memory for all settings
• Operating temperature range: -20…60°C
  • Accuracy (min): ± 0.4 °C (in -10…+ 60 °C range)
  • Accuracy (max): ± 0.6 °C (in -20…+ 60 °C range)
  • Resolution: 0.1 °C
• Operating relative humidity range: 10…90% (non-condensing)
  • Accuracy (min): ± 3.0 % RH (in 20…80 % RH range)
  • Accuracy (max): ± 5.0 % RH (in 10…90 % RH range)
  • Resolution: 0.1 % RH
• Ingress protection: IP20
• Operating voltage range: 4.5…26 VDC

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0...10 V / 2...10 V / 4...20 mA
• Option: LCD display
• Option: relay output
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP20

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0/2...5/10 VDC
• Option: LCD display
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP54

• Temperature measurement range:
  a) Ambient model: -20...+80 °C
  b) Remote model with polycarbonate probe: -20...+80 °C
  c) Remote model with stainless steel probe: -40...180 °C
• Relative humidity measurement range: 0...100 %
• Calculates dew point, absolute humidity, enthalpy and combination ratio
• 4-wire analog output: 0...5/10 V or 0/4...20 mA
• 2 relay outputs
• Versions with or without display
• Protection class: IP65 (ABS V0 housing)

• Universal input for measuring temperature, resistance and standard signal
• 4 alarm outputs with signaling on LED diodes
• Digital output: RS-485 modbus (can be programmed through RS-485)
• Analog signal output: 0/4...20 mA or 0...10 V
• Two-line LCD display
• Mathematical functions for converting the measured value
• Protection grade: frontal side – IP65 / from terminal side – IP10
• Operating temperature: -25...23...55 °C

Indoor temperature meter / transducer Txx18, designed for temperature, humidity and barometric pressure measurement.

• Ethernet connection
• Digital inputs: 2
• 1-Wire input (up to 2 sensors)
• Analog inputs: 2 (0...60 VDC)
• Relay outputs: 2 (NO/NC)
• IP watchdog function
• Webserver
• SNMP alarms
• VLAN and MAC address filtering
• Operating temperature: -20...55 °C
• Warranty: 3 years
• Supply: 10...14 VDC

• SpotScan is a linear scanning add-on for RAYTEK, IRCON noncontact IR thermometers ENDURANCE, Marathon MM, Modline 5 and Modline 7

• SpotScan is designed to broaden the capabilities of noncontact IR thermometers while scanning measured surface linearly thus measuring wider than one dot target area

The enLink OAQ Vape transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• Sensed parameters: Temperature, Relative humidity, VOC, CO2, Particles PM (1.0, 2.5, 4.0 & 10), Barometric pressure, Ozone**, Arsine*, Formaldehyde*, Methyl Mercaptan*, Chlorine*, Carbon Monoxide*, Ethylene Oxide*, Hydrogen*, Hydrogen Sulphide*, Hydrogen Cyanide*, Ammonia*, Nitrogen Dioxide*, Oxygen*, Odorous gases*, Phosphine*, Sulphur Dioxide*
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours
• Power supply: 12…24V V DC, 0.15 Amp (max) / 4 x Li-SOCl2 (3.6V) AA / external solar panel
• Configuration via USB cable / downlink
• IP rating: IP42 (conformally coated electronics), do not expose to direct sunlight
• Operating Temp. / Humidity: -10…40 °C / 0…95 % RH (be kondensacijos)

The enLink Status-T transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• External sensor measurement range: -55…+125 °C
  • Accuracy: ± 0.5 °C (-10…+85 °C)
• Up to two probes (cable length: 1 m, others on request)
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours or adaptive (triggered by alarm)
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Each sensor can be programmed individually for different alarm type: No alarming, High threshold alarm, Low threshold alarm, In band alarm, Out of band alarm
• Each alarm type has an individual alarm status message with the following parameters: Alarm status, Total number of alarm activations, Alarm duration
• Case IP40 protection (IP 67 on request)

The Wx9xx series of sensors from COMET SYSTEM enables accurate measurement of temperature, relative humidity, and atmospheric pressure, with data transmitted via the low-power LoRaWAN network. This technology allows data to be sent to a cloud storage, where users can easily view both current and historical values through a standard web browser. Each sensor has an LCD display showing the measured value and battery status.

• Possibility to connect Pt1000 sensors
• Covers up to 15 km in rural areas and 2…5 km in urban areas
• Work with Comet System LoRaWAN gateway SP041
• Battery life: from 1 to 10 years depending on transmission time and environment temperature
• Unlimited space for data in cloud
• Alarm: email and app notification
• Mobile applications for Android and iOS

• The battery or mains powered wireless M-Bus gateway B4 is highly configurable plug-and-play device used for collecting data from Wireless M-Bus meters / sensors and transmitting the data using LTE CAT-M1 and MQTT protocol
• Long range and high sensitivity internal (or external mounted) antennas
• To maximize the battery lifetime possible configuration to listen number of minutes, specific time during day, specific days and limit number of packets stored per meter / week / day / hour
• The gateway firmware can be upgraded remotely using MQTT
• B4 series gateway can be used with Lansen R4 series repeaters and transmit additional information (see datasheet)
• Configuration can be done with: Lansen Wireless M-BUS programming dongle together with our program, Lansen Configurator, other wireless M-BUS transmitters or remotely using the MQTT protocol
• Possible to activate 128 bit AES-key encryption
• Gateway suited for harsh environments, operating temperature: -30…+85 °C, protection class: IP40, IP65 and IP67
• IoT LTE M SIM card needed (acquired separately)

• Mounting brackets for easy installation of temperature sensors in measuring point
• UZ11 – full bracket
• UZ21 – bracket without body (only flange)
• Diameter: 15 / 22 / 32 mm
• Body and flange material: 1.0401 steel
• Sealing part material: Teflon / glass fiber
• High quality
• Complies with DIN EN 50 446

• Designed for air temperature and humidity sensors / transmitters
• Transmitter entirely protected inside the shield
• Prevention of condensation by downward sensor orientation
• Advanced weather protection by maximized top cover area (Ø 250 mm)
• Passively ventilated, requires no power
• Plate system permits air flow through the sensor
• ASA plastic is resistant to mechanical damage and UV radiation. It is anti-static and very stable over time.

• Measured parameters (with respective sensors):
  a) Temperature (Pt100 or thermocouple)
  b) Humidity
  c) Air quality
  d) Air velocity
  e) Airflow
  f) Tachometry
• Two inputs for Pt100 temperature sensors (range -200...600 °C)
• Up to 6 measurements simultaneously
• Power supply: Lithium-Ion battery (up to 57 hours)
• Calibration certificate, additional battery, transport case included
• Operating temperature: 0...50 °C
• Protection class: IP54

SIRO is an indoor air quality transmitter with a modern design. The transmitter is available with several optional air quality sensors. The modular device can be equipped with CO2 concentration and VOC (Volatile Organic Compounds) measurements or alternatively PM (Particulate Matter) measurement, and in addition, temperature and humidity measurements. SIRO-MOD series models use Modbus serial communication protocol.

• Measuring elements:
  • CO2: Non-dispersive infrared (NDIR); 0...2000 ppm
  • VOC: Complementary Metal Oxide Semiconductor (CMOS); range: * - see datasheet
  • PM: Laser-based light scattering particle sensing
  • Temperature: Integrated to CMOS
  • Relative humidity: Thermoset polymer capacitive sensing element
• Field configurable outputs for selected measurements; Configuration possible through MODBUS
• Proportional output options including voltage (0–10 V, 0–5 V, 2–10 V) and optional current (4–20 mA); MODBUS
• Offset feature enabling field calibration for each measurement parameter (CO2, VOC, PM, RH, T)
• Optional LCD-display and buttons
• Operating temperature: 0…50 °C
• Protection standard: IP20

Infrared temperature meter KIRAY 100 with double measuring laser. Main tool for temperature measurement in remote and dangerous areas.

Infrared temperature meter KIRAY 200 with double measuring laser. Main tool for temperature measurement in remote and dangerous areas.

Noncontact infrared thermometer KIRAY 300 is designed to diagnose, inspect and check the surface temperature of measured objects. Up to 100 values can be stored in the internal memory.

• Noncontact infrared temperature meter 3i Plus (pyrometer), designed for metalworking industry where casting, hardening, heating take place. Also suitable for ceramics, semiconductor, chemical furnace temperature measurement
• It is a new generation, small size IR device for high temperature measurement
• Precise high-resolution optics guarantee high accuracy, resistant casing let the device survive falls from up to 1 meter height
• That said, measurements can be done in various environments and from various distances

• Noncontact stationary infrared temperature meter CM for temperature measurement
• Range: -20...500 °C
• Outputs: 0...5V, or TC K / J type (chosen while ordering)
• Software “DataTemp Multidrop” for remote monitoring and configuration

• Noncontact infrared thermal meter (pyrometer) ENDURANCE
• for temperature measurement up to 3200 ºC with the resolution of 0,1 ºC
• Outputs: Ethernet, profinet, 0/4...20mA (isolated), RS485, relay 48V and 300mA
• Web server
• Wider area can be measured when used with SpotScan

• Noncontact infrared thermal meter Marathon MM, wide range of accessories for various applications
• Range: -40...3000°C (in fixed ranges)
• Outputs: 0/4...20mA, RS485, mechanical switch

• Noncontact infrared thermal meter Thermalert TX, additional accessories for various applications
• Can be used in an explosive area
• Range: -18...2000 °C (in fixed ranges)
• Outputs: 4...20mA, HART į RS232, mechanical switch (depends on version)

• Grain temperature monitoring system software for PC
• Collects data from temperature cables GWSL 1100 and GWSL 2100 and spear temperature sensors GWTL-R
• Stores, visualizes data in charts
• Alarms
• Level indication

The instrument uses a pH/ORP sensor and RTD Pt100 temperature sensors. If the Pt100 is connected the transmitter makes automatic temperature compensation (pH only).

• pH range: 0 ÷ 14.00 pH
• ORP range: 0 ÷ 1000 / 0 ÷ -1000 / -1000 ÷1000 / 0 ÷ 2000 / 0 ÷ -2000 mV
• Temperature range: -10.0 ÷ 110.0 °C / 14.0 ÷ 230.0 °F
• Resolution: 0.01 pH, 1 mV, 0.1 °C
• Digital output: RS-485 isolated
• Analog output: 4-20 mA galvanically isolated, "current loop" two wires
• Power supply: 9 / 36 Vdc
• Dimensions: 71x95x58 mm. Rail Din (4 modules)
• Operating temperature: 0…+50 °
• EMC/RFI conformity: EN 61326

Instrument PH135 is designed for liquid pH, ORP and temperature measurement.

• pH measuring range: -1.00/15.00 pH, accuracy 0.01 pH
• ORP measuring range: -1200/+1200 mV, accuracy 1 mV
• Temperature measuring ranges: -10.0/+110.0 °C ;  -14.0/+230.0 °F
• Alphanumeric LCD display
• Manual and automatic temperature compensation
• Manual or automatic calibration
• Automatic recognition of buffer solutions
• Data logging up to 100 measures
• Alcaline 9 V battery
• Dimensions: 92 x 155 x 33 mm  -  Weight:  approx. 300 g 

PoE (power over Ethernet) temperature, relative air humidity, atmospheric pressure meters T4611, T3611, T7611. Only to be used with external sensors.

Application:

• Storage rooms
• Greenhouses
• Telecommunication devices
• Servers
• A/C units

PoE (power over Ethernet) temperature, relative air humidity, atmospheric pressure meters T0610, T3610, T7610. Only to be used with internal sensors.

Application:

• Storage rooms
• Greenhouses
• Telecommunication devices
• Servers
• A/C units

• RS-485 protocol temperature and humidity sensor
• Temperature measurement range: -20...+60 °C
• Accuracy: ±0,13 °C
• Resolution: 14 bits
• Very low current consumption
• Warranty: 3 years
• Connection: RJ-45

• Output 4...20 mA
• Supply 90...250 VAC

• Ethernet connection
• Digital inputs: 2
• 1-Wire input (up to 2 sensors)
• Analog inputs: 2 (0...60 VDC)
• Relay outputs: 2 (NO/NC)
• Webserver
• HTTP and XML API commands
• E-mail alarms, SMTP, SNMP
• Operating temperature: -20...55 °C
• Warranty: 3 years
• Supply: 10...14 VDC

Temperature regulator SCD210 is designed for temperature control in various devices and rooms. Made in three variants with different inputs. SCD210 has a step set point (SP) value change by signal option in binary input.

• Up to 60 logical channels for data logging (max. up to 8 analog channels)
• Inputs:
  • Measuring programmable: 0, 4 or 8
  • Binary: 2 or 6
  • Modbus RTU Client: 10 devices, 10 registers each
• Outputs:
  • Relay: 2, 6 or 8
  • Analog 0 / 4...20 mA: 0, 4 or 8
  • Supplying output for external devices: 24V d.c. / 30 mA
• Communication interfaces:
  • RS-485 MODBUS (Client and Server)
  • Ethernet: MODBUS TCP/IP, Webserver (www), FTP
  • USB Host 2.0
• Screen: Graphical color display LCD TFT 3.5”
• Internal memory 8 GB for Archiving of measured parameters
• Visualization of measurements in digital form, analog indicators, line charts, bargraphs
• Advanced mathematical functions on measured values
• Archiving and visualization of measuring data transmitted to KD6 from external devices via RS-485 MODBUS 
• Settings secured with access password
• PC software for easier setup
• Protection class: IP65 (front)
• Operating temperature: -10...55 °C
• Supply: 85...253 V a.c., 90...300 V d.c. or 20...60 V d.c.

• Input: 4x RTD (Pt100, Pt1000, Ni100, Ni1000), resistive and potentiometer configurable input
• Output: RS-485 Master/Slave and RS-232 (MODBUS RTU/ASCII protocol)
• 2000 VAC galvanic isolation
• High accuracy
• EMC compliance - CE symbol
• Mounting on DIN rail - EN-50022 complience
• Supply voltage: 10...30 VDC
• Ambient temperature: -10...+60°C

• Modbus Slave over RS-485
• Modbus RTU / Modbus ASCII protocols
• Communication parameters configurable by dip-switches
• Watch-dog alarm
• Remotely configurable
• 3-way galvanic isolation (1500 VAC)
• High accuracy
• Mounting on DIN rail - EN-50022 compliance