Преобразователи

• Data converter which connects reader in safe zone with network switches and temperature cables/spears in dangerous zone
• Input: 4 x temperature cables (from switches GWNET11 and cables GWSL 1100 or GWSL 2100)
• Output: Modbus RTU, RS-485
• Reads data from 68 individual temperature cables and spears
• Supply: 230 VAC / 115 VAC
• Protection class: IP66
• Certificates: IECEx, ATEX

• Works as a multiplexer, enabling 4 additional temperature cables or spears to be connected to GWAB11 converter
• Another GWNET11 can be connected in parallel, further expanding inputs of GWAB11 by 4
• Operating temperature: -20...+50 °C
• Protection class: IP66
• Certificates: IECEx, ATEX

• Digital inputs: 2
• 1-Wire input (up to 8 sensors)
• RS-485 input (up to 8 sensors)
• Analog inputs: 4 (2 x 0...10 VDC, 2 x 0...10 VDC / 4...20 mA, WEB control)
• Relay outputs: 4 (NO/NC)
• Setup via USB or SMS
• Data logger for up to 52 000 records
• Webserver
• Periodical upload of data logger file to a remote HTTP server
• HTTP Post, HTTP API
• SMS alarms (up to 5 numbers)
• E-mail alarms (up to 5 recipients), SMT with TLS support
• Operating temperature: -20...55 °C
• Warranty: 3 years
• Supply: 10...24 VDC

• Digital inputs: 2
• 1-Wire input (up to 4 sensors)
• Analog inputs: 2 (0...60 VDC)
• Relay outputs: 2 (NO/NC)
• Setup via USB or SMS
• Webserver
• HTTP Post, HTTP API
• SMS alarms (up to 5 numbers)
• E-mail alarms (up to 5 recipients), SMTP with TLS support
• Operating temperature: 0...40 °C
• Warranty: 3 years
• Supply: 10...28 VDC

• Enables the PC to be connected to HART interface, i.e. to configure a device
• Active operation: current loop is supplied
• Passive operation: used in an existing current loop
• Included HART-Tool software
• Supply: from USB
• Galvanic isolation between USB and HART

• Communicates with devices supporting HART and LHP interfaces
• Supports universal, common commands
• HART connector: BNC
• Supply: 9 V accumulator (charged via USB)
• Operating temperature: -20...+50 °C
• Operating humidity: 0...80 % RH
• Protection class: IP40

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0...10 V / 2...10 V / 4...20 mA
• Option: LCD display
• Option: relay output
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP20

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0/2...5/10 VDC
• Option: LCD display
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP54

• Temperature measurement range:
  a) Ambient model: -20...+80 °C
  b) Remote model with polycarbonate probe: -20...+80 °C
  c) Remote model with stainless steel probe: -40...180 °C
• Relative humidity measurement range: 0...100 %
• Calculates dew point, absolute humidity, enthalpy and combination ratio
• 4-wire analog output: 0...5/10 V or 0/4...20 mA
• 2 relay outputs
• Versions with or without display
• Protection class: IP65 (ABS V0 housing)

• Long-life metal-oxide gas sensor
• Range 0...100 % LEL H₂
• Resolution 0,1 % LEL H₂
• Outputs 2 x 4...20 mA / 0...10 V, RS-485
• Attached or remote sensor options

• Hydrogen pressure transmitter’s measuring principle: Thin-film-on-steel
• EC79 and ECER-134 certification pending (see product website for current situation)
• Applications: Fuel cells, fueling stations, hydrogen compressors, hydrogen tanks, vehicles with H drive
• Measuring range: 0…1050 bar / 0…15000 psi *(see product datasheet)
• Measuring accuracy at 25 °C typ.: ± 0.3 / 0.5 % FS typ.
• Output signal: 4...20 mA, 0.5...4.5 VDC, 0...5 VDC, 1...5 VDC, 1...6 VDC, 0...10 VDC, 0.1...10.1 VDC, 0.5...4.5 VDC ratiometric, Switching output: 1 or 2 PNP
• Pressure connections: G1/4" m, 1/4"NPT m, 7/16"-20UNF SAE4 m
• Ambient temperature: 40°C…+85°C

• Stable long-life electrochemical gas sensor
• Range 0...100 / 0...1000 ppm H₂S
• Resolution 0,1 / 1 ppm H₂S
• Outputs 2 switches, 2 x 4...20 mA / 0...10 V, RS-485
• Default alarm set-points 10 / 20 ppm H₂S

• Stable long-life electrochemical gas sensor
• Range 0...100 / 0...1000 ppm H₂S
• Resolution 0,1 / 1 ppm H₂S
• Outputs 2 x 4...20 mA / 0...10 V, RS-485
• Attached or remote sensor option

• Electrochemical gas sensor
• Range: 0...100 / 0...2000 ppm H₂S
• Resolution: 0,1 / 1 ppm H₂S
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Option: relay output (2 x SPST) / LCD indicator
• Option: remote sensor (default cable length is 3 m)
• Operating temperature: -40...+50 °C
• Supply: 11...30 VDC / 24 VAC or 90...265 VAC

• Measurement of parameters: voltage, current, active, reactive and apparent power, cosφ, tgφ, frequency, active, reactive and apparent energy, active power 15 minutes, voltage 10 minutes
• Current and voltage harmonics analysis up to 51st (measurements available via RS-485)
• Programmable input:
  • Current: 0…1 / 0…5A
  • Voltage: 0…100V / 0…230V / 0…400V
• Output:
  • Analog: 0/4...20 mA or 0...10 V
  • Relays: 1 or 4
  • Binary (OC)
• Digital output: RS-485 modbus (can be programmed through RS-485)
• Two-line LCD display
• Pulse output to measure energy consumption
• 4 alarm outputs with signaling on LED diodes, working in 7 different modes
• Conversion of any measured value into an analog signal 0/4...20 mA or 0...10V
• Protection grade: frontal side – IP65 / from terminal side – IP10
• Operating temperature: -25...23...55 °C

Industrial IoT module TCW242 for remote real-time monitoring and control of industrial equipment, facilities, production lines, renewable energy systems, greenhouses and water stations

• Web-based configuration and control with password protection
• 4 digital inputs for dry contacts
• 4 analog inputs with 0-10V and 0-20mA options
• 4 relays with normally open/normally closed contacts
• RS-485 interface for MODBUS RTU sensors. Up to 24 sensors (registers)
• Monitor up to 24 channels
• Set up to 24 independent alarms
• SNMPv3 protocol support
• Alarm notifications via SNMP traps
• NTP protocol support
• HTTP API commands
• 4 schedules for real-time control of relay outputs
• Custom logical functions
• Secured email transfer with TLS 1.0, TLS 1.1, and TLS 1.2 support
• Data logging capacity for up to 70,000 records
• Dynamic DNS support for DynDNS, No-IP, and DNS-O-Matic providers
• Periodical HTTP / HTTPS Post of XML / JSON status files for client-server systems
• MODBUS TCP / IP protocol support
• MQTT 3.1.1 protocol support
• Rugged DIN-Rail / wall-mountable enclosure
• Operating temperature range: -20…+55 °C

• Industrial pressure transmitter’s measuring principle: Thin-film-on-steel
• Applications: hydraulics, industrial applications, machine tools
• 5-fold overpressure resistance
• Measuring range: 0...2.5 / 0...700 bar // 0...30 / 0...10000 psi
• Measuring accuracy at 25 °C typ.: ± 0.5 % FS typ. ± 0.3 % FS typ
• Output signal: 4...20 mA, 0...5 VDC, 0.5...5 VDC, 1...6 VDC, 0...10 VDC, 0.5…4.5 VDC ratiometric
• Ambient temperature: -40°C…+125°C

• Ethernet connection
• Digital inputs: 2
• 1-Wire input (up to 2 sensors)
• Analog inputs: 2 (0...60 VDC)
• Relay outputs: 2 (NO/NC)
• IP watchdog function
• Webserver
• SNMP alarms
• VLAN and MAC address filtering
• Operating temperature: -20...55 °C
• Warranty: 3 years
• Supply: 10...14 VDC

• Connected to a liquid manometer, measure dynamic pressure in a pipe and determine its speed (in range: 0...100 m/s) and flow m3/h
• Sheathed thermocouple K probe integrated, with connection cable length 1,5 m (option)
• Introduced perpendicularly in the pipe
• Particularly adapted for measurement in warm air, charged with particles and for high speed
• Accuracy: Better than 1 % for an alignment in relation to the flow axis of the fluid of ± 10 °
• Coefficient: 1,0015 ± 0,01
• Max static pressure: 2 bar
• Temperature of use: 0…600 °C (up to 1000 °C in option)

The new leak meters LD 500/510 with integrated camera and leakage calculation are ideal to find even smallest leakages (0.1 l/min) easily even in far distances and calculate potential saving (€/year).

• 30 MEMS digital microphones for image of leaks
• Measuring distance: up to 6,5 m
• 3,5” TFT color display with touch panel
• Additional sensor input to measure: dew point, flow, pressure, and temperature (LD 510 only. See datasheet)
• Possibility to take photo of leaking parts
• Data transfer via USB to PC
• Easy data and work assignment with CS Leak Reporter cloud solution
• ISO 50001 report
• Power supply: 7,2 V lithium-ion battery (> 9 h continuous operation)
• Operating temperature: -5…+40 °C

• Incremental encoder output: A, B   /   A, B, Z   /   A, /A, B, /B   /   A, B, Z, /A, /B, /Z
• Resolution: 5 / 10 / 25 / 50 μm
• Magnetic measurement (contactless, non-friction system)
• Vibration-resistant
• Cable length: 3 / 5 / 8 / 10 m (optionally 5...50 m)
• Supply: 10...30 VDC / 5 VDC
• Operating temperature: -25...+85 °C
• Protection class: IP67

• Incremental encoder output: A, B   /   A, B, Z   /   A, /A, B, /B   /   A, B, Z, /A, /B, /Z
• Resolution: 5 / 10 / 25 / 50 μm
• Portable reference point
• Stroke values up to 2000 mm
• Vibration-resistant
• Cable length: 3 / 5 / 8 / 10 m (optionally 5...50 m)
• Supply: 10...30 VDC / 5 VDC
• Operating temperature: -25...+85 °C
• Protection class: IP65

The enLink Status-VC transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• 0…20 mA, 0…10 V or resistance input
• 12 bit resolution
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Case IP40 protection (IP 67 on request)

The enLink OAQ Vape transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• Sensed parameters: Temperature, Relative humidity, VOC, CO2, Particles PM (1.0, 2.5, 4.0 & 10), Barometric pressure, Ozone**, Arsine*, Formaldehyde*, Methyl Mercaptan*, Chlorine*, Carbon Monoxide*, Ethylene Oxide*, Hydrogen*, Hydrogen Sulphide*, Hydrogen Cyanide*, Ammonia*, Nitrogen Dioxide*, Oxygen*, Odorous gases*, Phosphine*, Sulphur Dioxide*
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours
• Power supply: 12…24V V DC, 0.15 Amp (max) / 4 x Li-SOCl2 (3.6V) AA / external solar panel
• Configuration via USB cable / downlink
• IP rating: IP42 (conformally coated electronics), do not expose to direct sunlight
• Operating Temp. / Humidity: -10…40 °C / 0…95 % RH (be kondensacijos)

The enLink Status-P transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• 3 channels pulse counter (S0 standard) and monitor of state (open / closed)
• With the transmit on Change of State enabled the unit operates as a standard pulse counter and also transmits a message when the state of the input changes from closed to open or open to closed
• The pulse counts for each channel are written to memory every 5 – 10 minutes
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours or adaptive (triggered by change of state)
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Case IP40 protection (IP 67 on request)

The enLink Status-T transmits data using long range LoRa wireless which easily integrates with cloud services or on-site Systems.

• External sensor measurement range: -55…+125 °C
  • Accuracy: ± 0.5 °C (-10…+85 °C)
• Up to two probes (cable length: 1 m, others on request)
• Communication: LoRaWAN; frequency range: 863-870 MHz; up to 16 km range
• Measurement sending interval: 30 s to 3 hours or adaptive (triggered by alarm)
• 2 x Li-SOCl2 (3.6V) AA sized batteries ensure 3+ years of operation
• Configuration via USB cable / downlink
• Each sensor can be programmed individually for different alarm type: No alarming, High threshold alarm, Low threshold alarm, In band alarm, Out of band alarm
• Each alarm type has an individual alarm status message with the following parameters: Alarm status, Total number of alarm activations, Alarm duration
• Case IP40 protection (IP 67 on request)

The Wx9xx series of sensors from COMET SYSTEM enables accurate measurement of temperature, relative humidity, and atmospheric pressure, with data transmitted via the low-power LoRaWAN network. This technology allows data to be sent to a cloud storage, where users can easily view both current and historical values through a standard web browser. Each sensor has an LCD display showing the measured value and battery status.

• Possibility to connect Pt1000 sensors
• Covers up to 15 km in rural areas and 2…5 km in urban areas
• Work with Comet System LoRaWAN gateway SP041
• Battery life: from 1 to 10 years depending on transmission time and environment temperature
• Unlimited space for data in cloud
• Alarm: email and app notification
• Mobile applications for Android and iOS

• The battery or mains powered wireless M-Bus gateway B4 is highly configurable plug-and-play device used for collecting data from Wireless M-Bus meters / sensors and transmitting the data using LTE CAT-M1 and MQTT protocol
• Long range and high sensitivity internal (or external mounted) antennas
• To maximize the battery lifetime possible configuration to listen number of minutes, specific time during day, specific days and limit number of packets stored per meter / week / day / hour
• The gateway firmware can be upgraded remotely using MQTT
• B4 series gateway can be used with Lansen R4 series repeaters and transmit additional information (see datasheet)
• Configuration can be done with: Lansen Wireless M-BUS programming dongle together with our program, Lansen Configurator, other wireless M-BUS transmitters or remotely using the MQTT protocol
• Possible to activate 128 bit AES-key encryption
• Gateway suited for harsh environments, operating temperature: -30…+85 °C, protection class: IP40, IP65 and IP67
• IoT LTE M SIM card needed (acquired separately)

• Long-lasting stainless steel screw electrodes
• Measurement range: 7...20 % (-40...+125 °C)
• Resolution: 0,1 %
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Electrode cable: FEP, -50...+200 °C, 5/10/15 m
• Timber temperature compensation
• Electrode length: 15 / 25 mm
• Supply: 11...30 VDC
• Protection class: IP68

• Stable long-life metal-oxide gas sensor
• Range 0...100 % LEL (0...5 % vol) CH₄
• Resolution 0,1 % LEL (50 ppm) CH₄
• Outputs 2 switches, 2 x 4...20 mA / 0...10 V, RS-485
• Default alarm set-points 20 / 50 % LEL CH₄

• Stable long-life metal-oxide gas sensor
• Range 0...100 % LEL CH₄
• Resolution 0,1 % LEL CH₄
• Outputs 2 switches, 2 x 4...20 mA / 0...10 V, RS-485
• Default alarm set-points 20 / 50 % LEL CH₄
• Visual and acoustic alarms

• Stable long-life metal-oxide gas sensor
• Range 0...100 % LEL (0...5 % vol) CH₄
• Resolution 0,1 % LEL (50 ppm) CH₄
• Outputs 2 x 4...20 mA / 0...10 V, RS-485
• Attached or remote sensor options

• Metal-oxide gas sensor
• Range: 0...100% LEL (0...5 %) CH₄
• Resolution: 0,1 % LEL (50 ppm) CH₄
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Option: relay output (2 x SPST) / LCD indicator
• Option: remote sensor (default cable length is 3 m)
• Operating temperature: -40...+70 °C
• Supply: 11...30 VDC / 24 VAC or 90...265 VAC

• Input: Modbus RTU – RS-485
• Output: 4-channel SPST relay contacts
• Rated relay load: 3 A at 250 Vac; 3 A at 30 Vdc
• Non-volatile memory to retain and restore relay states following power outages
• Watchdog functionality for communication loss
• Operating temperature / humidity: -20…+60 °C / 10…90 % (non-condensing)
• DIN rail mounting
• Power supply: 5…28 Vdc
• Warranty: 3 years

• Designed for air temperature and humidity sensors / transmitters
• Transmitter entirely protected inside the shield
• Prevention of condensation by downward sensor orientation
• Advanced weather protection by maximized top cover area (Ø 250 mm)
• Passively ventilated, requires no power
• Plate system permits air flow through the sensor
• ASA plastic is resistant to mechanical damage and UV radiation. It is anti-static and very stable over time.

SIRO is an indoor air quality transmitter with a modern design. The transmitter is available with several optional air quality sensors. The modular device can be equipped with CO2 concentration and VOC (Volatile Organic Compounds) measurements or alternatively PM (Particulate Matter) measurement, and in addition, temperature and humidity measurements. SIRO-MOD series models use Modbus serial communication protocol.

• Measuring elements:
  • CO2: Non-dispersive infrared (NDIR); 0...2000 ppm
  • VOC: Complementary Metal Oxide Semiconductor (CMOS); range: * - see datasheet
  • PM: Laser-based light scattering particle sensing
  • Temperature: Integrated to CMOS
  • Relative humidity: Thermoset polymer capacitive sensing element
• Field configurable outputs for selected measurements; Configuration possible through MODBUS
• Proportional output options including voltage (0–10 V, 0–5 V, 2–10 V) and optional current (4–20 mA); MODBUS
• Offset feature enabling field calibration for each measurement parameter (CO2, VOC, PM, RH, T)
• Optional LCD-display and buttons
• Operating temperature: 0…50 °C
• Protection standard: IP20

• Electrochemical gas sensor
• Range: 0...250 ppm NO
• Resolution: 1 ppm NO
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Option: relay output (2 x SPST) / LCD indicator
• Option: remote sensor (default cable length is 3 m)
• Operating temperature: -30...+50 °C
• Supply: 11...30 VDC / 24 VAC or 90...265 VAC

• Stable long-life electrochemical gas sensor
• Range 0...20 / 0...200 ppm NO₂
• Resolution 0,02 / 0,1 ppm NO₂
• Outputs 2 switches, 2 x 4...20 mA / 0...10 V, RS-485
• Default alarm set-points 3 / 6 ppm NO₂

• Stable long-life electrochemical gas sensor
• Range 0...20 / 0...200 ppm NO₂
• Resolution 0,02 / 0,1 ppm NO₂
• Outputs 2 x 4...20 mA / 0...10 V, RS-485

• Electrochemical gas sensor
• Range:
• -- 0...20 ppm NO₂
• -- 0...200 ppm NO₂
• Resolution:
• -- 0,1 ppm NO₂ for 20 ppm range
• -- 1 ppm NO₂ for 200 ppm range
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Option: relay output (2 x SPST) / LCD indicator
• Option: remote sensor (default cable length is 3 m)
• Operating temperature: -20...+50 °C
• Supply: 11...30 VDC / 24 VAC or 90...265 VAC

• Stable long-life electrochemical gas sensor
• Range 0...20 % vol O₂
• Resolution 0,01 % vol O₂
• Outputs 2 switches, 2 x 4...20 mA / 0...10 V, RS-485
• Default alarm set-points 19,5 / 18 % vol O₂

• Stable long-life electrochemical gas sensor
• Range 0...20 % vol O₂
• Resolution 0,01 % vol O₂
• Outputs 2 x 4...20 mA / 0...10 V, RS-485
• Attached or remote sensor options

• Electrochemical gas sensor
• Range: 0...25 % O₂
• Resolution: 0,01 % O₂
• Analog output: 2 x 4...20 mA / 0...10 V (user-settable)
• Digital output: RS-485 (Modbus RTU protocol)
• Option: relay output (2 x SPST) / LCD indicator
• Option: remote sensor (default cable length is 3 m)
• Operating temperature: -30...+50 °C
• Supply: 12...36 VDC, 24 VAC or 230 VAC

The instrument uses a pH/ORP sensor and RTD Pt100 temperature sensors. If the Pt100 is connected the transmitter makes automatic temperature compensation (pH only).

• pH range: 0 ÷ 14.00 pH
• ORP range: 0 ÷ 1000 / 0 ÷ -1000 / -1000 ÷1000 / 0 ÷ 2000 / 0 ÷ -2000 mV
• Temperature range: -10.0 ÷ 110.0 °C / 14.0 ÷ 230.0 °F
• Resolution: 0.01 pH, 1 mV, 0.1 °C
• Digital output: RS-485 isolated
• Analog output: 4-20 mA galvanically isolated, "current loop" two wires
• Power supply: 9 / 36 Vdc
• Dimensions: 71x95x58 mm. Rail Din (4 modules)
• Operating temperature: 0…+50 °
• EMC/RFI conformity: EN 61326

Measurement of 54 power network parameters, including current and voltage harmonics up to 63rd in 1-phase 2-wire or 3-phase 3 or 4-wire balanced and unbalanced systems

• High accuracy class (0.2S for active energy)
• Interface: RS-485 (Modbus RTU 8N2,8E1,8O1,8N1)
• Graphical color display: LCD TFT 3,5’’, 320 x 240 pixels, fully configurable by a user (10 screens, 8 parameters in each)
• Additional 2 screens for harmonics presentation and 1 dedicated screen for visualization in the form of an analog meter
• Memory of minimum and maximum values
• 2 configurable alarm outputs
• Supervisory relay mode for alarm outputs
• Password protection
• Programming of parameters using free eCon software
• Battery backup RTC
• Supply: 85...253 V ac / 90...300 V dc
• Operating temperature: -10…23…+55 °C
• Overall dimensions: 96 x 96 x 77 mm

• Measuring range: -1…100 bar (see datasheet)
• Basic accuracy 0,5% of range
• Output: 4…20 mA
• Process connection: G 1/2“, G 1/2“, G 1/2“ Flush membrane, G 1/4“, G 1/4“, 1/2“ NPT, 1/4“ NPT, Tri-Clamp (Ø 50,5) Flush membrane
• Operating temperature: -20…+85 / 200 °C (see datasheet)
• Stainless steel housing and diaphragm material
• Protection class: IP67 / IP68

• Pressure range: from 0...2,5 to 0...700 bar
• Process temperature: -40...+125 °C
• Process connection: G1/4" m, G1/4" m (Manometer), 1/4"NPT m, 1/8"NPT m, 7/16"-20UNF SAE J512 f, 7/16"-20UNF SAE4 m, 7/16"-20UNF m DIN3866, R1/4" m DIN3858, R1/4" m DIN2999, R1/8" m, M10x1 m, M12x1.5 m
• Protection class: IP65, IP67

• Pressure transmitter ATM (analog output)
• Pressure measurement range: from 0 to 0,1...1000 bar
• Accuracy: < ± 0,50 / 0,25 / 0.10 % FS
• Output: 0...5 VDC / 0...10 VDC / 0...20 mA / 4...20 mA
• Process connection: G 1/4 F, 1/4 NPT, 1/2 NPT, G 1/4 M, G1/2 M
• Process temperature: -40...150 °C
• Operating temperature: -25..85 °C
• Materials: stainless steel, titanium

• Pressure transmitter ATM.1ST/Ex (high precision, for explosive Ex environment)
• Various pressure measurement ranges: 0,1...1000 bar
• Accuracy: ≤ ± 0.10 / 0.05 % FS
• Output: 4...20 mA
• Process temperature: -40...150 °C
• Operating temperature: -40...125 °C
• Materials: stainless steel, titanium
• Certificates: ATEX, IECEx, EAC, GL/DNV, ABS, Lloyds

• Pressure transmitter ATM/Ex (for explosive Ex environment)
• Various pressure measurement ranges: 0,1...1000 bar
• Accuracy: ≤ ± 0.50 / 0.25 / 0.10 % FS
• Output: 4...20 mA
• Process temperature: -40...150 °C
• Operating temperature: -25...85 °C
• Materials: stainless steel, titanium
• Certificates: ATEX, IECEx, EAC