Temperature transducers

• The P20 programmable transducer is designed to convert temperature, resistance, voltage from a shunt and standard signals into a constant-current or constant-voltage standard signal
• The output signal is galvanicaly isolated from the input signal and supply
• The transducer is fully configurable through the PD14 programmer and free LPConfig software.

• Input: 2x thermocouples - J, K, T, N, E, B, R, and S
• Output: Modbus RTU – RS-485
• Resolution: 24 bits with DSP processing
• Working isolation voltage: 1500 Vrms
• Operating temperature / humidity: -20…+60 °C / 10…90% (non-condensing)
• DIN rail mounting
• Power supply: 5…30 Vdc
• Warranty: 3 years

• Temperature measurement range: -30...+80 °C
• Humidity measurement range: 0...100 %
• Output: RS-485 Modbus RTU
• Calculates absolute humidity and dew-point temperature
• Cable length: 2 m / 2 m with M8 connector / 5 m / 10 m
• Operating temperature: -20...+60 °C
• Supply: 9...28 VAC/VDC

• Ambient temperature and humidity transducer with 4...20 mA output
• Integrated sensors
• Calibration certificate is included
• Economical

Temperature transducers P4141, P4121, P4151, P4131, P4161, P4171, P4191 with 4...20 mA output and Pt1000 input.

P4121 – P4171 class transducers are designed to convert RTD Pt1000 (3850ppm/°C) signal to current. These transducers have 4...20 mA output. RTD sensor Pt1000 is not included.

• Pressure measurement range: -250...2500 / -250...7000 Pa
• Input: 2 x  0...10 V, NTC10k, Pt1000, Ni1000, binary
• Output: Modbus RTU
• Temperature compensation in range of 0...50 °C
• Allowed overpressure: 25 kPa
• Supply: 24 VDC/VAC
• Operating temperature: -20...+50°C
• Protection class: IP54

• PID controller
• Pressure measurement range: 0...2500 Pa
• Modbus RTU communication
• Control output: 0...10 V
• External input: 0...10 V / thermistor / binary
• LCD display
• Temperature compensation
• Allowed overpressure: 25 kPa
• Supply: 24 VDC
• Operating temperature: -20...+50°C
• Protection class: IP54

Duct temperature transducer with 4...20 mA output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Calibration certificate is included.

Duct temperature transducer with 0...10 V output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Output temperature range is user adjustable. Calibration certificate is included.

• Grain temperature monitoring system for steel and concrete bins
• Digital sensors with 2-wire bus
• Sensor spacing: 2 or 3 m
• Diameter: Ø9,8 mm
• Length: 1...35 m
• Tensile strength: ≤ 2,5 t
• Operating temperature -20...50 °C
• Maximal surface temperature 85 °C
• System is ATEX-, IECEx- and GOST-R approved
• ATEX approval code: Ex II 1D Ex ia IIIC T85°C

• Grain temperature monitoring system for steel and concrete bins
• Digital sensors with 2-wire bus
• Sensor spacing: 2 or 3 m
• Diameter: Ø17 mm
• Length: 1...100 m
• Tensile strength: ≤ 8 t
• Operating temperature -20...50 °C
• Maximal surface temperature 85 °C
• System is ATEX-, IECEx- and GOST-R approved
• ATEX approval code: Ex II 1D Ex ia IIIC T85°C

At extra cost: 2 analog outputs (0...10V, 4...20mA), membranous filter, teflon filter, bronze filter.

The sensor changes measured parameters to an analog or a digital signal.

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0...10 V / 2...10 V / 4...20 mA
• Option: LCD display
• Option: relay output
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP20

• Temperature measurement range: 0...50 °C
• Humidity measurement range: 0...100 %
• Output: 2 x 0/2...5/10 VDC
• Option: LCD display
• Option: Modbus RTU
• Supply: 24 VDC/VAC
• Operating temperature: 0...50 °C
• Protection class: IP54

• Temperature measurement range:
  a) Ambient model: -20...+80 °C
  b) Remote model with polycarbonate probe: -20...+80 °C
  c) Remote model with stainless steel probe: -40...180 °C
• Relative humidity measurement range: 0...100 %
• Calculates dew point, absolute humidity, enthalpy and combination ratio
• 4-wire analog output: 0...5/10 V or 0/4...20 mA
• 2 relay outputs
• Versions with or without display
• Protection class: IP65 (ABS V0 housing)

The P18L transducer is a device destined for the continuous measurement and conversion of relative humidity and ambient temperature into a standard analog signal 4...20mA.

• P18L transducer is supplied from a current loop.
• Applied sensor shields enable the application of the P18L transducer to operate in various ambient conditions.

• Universal input (for standard signals and temperature sensors)
• Alarm output
• OLED display
• Configuration via miniUSB connector
• Supply: 24 VDC or 230 VDC / VAC
• IP65 protection class

• The module setting can be done through USB or one of the RS-485 (master/slave) interface using the available for free eCon program
• Possibility of connection via internal RS-485 port in order to increase no of analog outputs in network
• Master Modbus function dedicated to read out data from other RS-485 devices and to scale analog value.
• Slave Modbus function to set the signal on analog outputs
• Possibility of configuration through USB without power supply

• 4 analog inputs (standard signals, RTD, thermocouple)
• RS-485 Modbus output (Slave mode)
• 2 alarm outputs
• Galvanic isolation of inputs (2 from other 2)
• Programmable individual characteristics, mathematical functions
• Programmable time counters
• Rail-mounted

Analog signal / RS-485 converter SM1.

Analog signal / RS-485 converter SM2.

• Designed for air temperature and humidity sensors / transmitters
• Transmitter entirely protected inside the shield
• Prevention of condensation by downward sensor orientation
• Advanced weather protection by maximized top cover area (Ø 250 mm)
• Passively ventilated, requires no power
• Plate system permits air flow through the sensor
• ASA plastic is resistant to mechanical damage and UV radiation. It is anti-static and very stable over time.

• Output 4...20 mA
• Supply 90...250 VAC

Relative humidity and temperature transducer P18D with display and RS-485 output, designed for temperature and humidity measurement.

• Input: 4x RTD (Pt100, Pt1000, Ni100, Ni1000), resistive and potentiometer configurable input
• Output: RS-485 Master/Slave and RS-232 (MODBUS RTU/ASCII protocol)
• 2000 VAC galvanic isolation
• High accuracy
• EMC compliance - CE symbol
• Mounting on DIN rail - EN-50022 complience
• Supply voltage: 10...30 VDC
• Ambient temperature: -10...+60°C

The P17 transducer, supplied from a current loop, converts the signal from temperature sensors or a standard voltage signal into a 4...20 mA current.

• Modbus Slave over RS-485
• Modbus RTU / Modbus ASCII protocols
• Communication parameters configurable by dip-switches
• Watch-dog alarm
• Remotely configurable
• 3-way galvanic isolation (1500 VAC)
• High accuracy
• Mounting on DIN rail - EN-50022 compliance

• Ethernet 10/100 Base-T interface
• Modbus TCP server
• Webserver for configuration of device and representation of actual input values
• Galvanic isolation on all the ways (1500 VAC)
• Remotely configured
• LED indication
• EMC compliance
• DIN rail mounting

Temperature and air humidity transducer P19 with RS-485 output, designed for room humidity ant temperature contro. Can be used in various control and monitoring systems. Output signal is digital (RS-485, MODBUS). Transducer parameters are programmed via PC. Wall-mounted. Can work in condensation-free environment.

• Integrated temperature and humidity sensor
• Calculated values – dew point temperature, absolute humidity
• Minimal and maximal value memory
• Isolated RS-485 port

Temperature and humidity transmitter with 4-20mA output.

• Measures air temperature, humidity in ducts
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measurement ranges: -30...125 °C / 0...100 %RH
• Operating temperature: -30...+60 °C
• Ex marking: EX II 3G Ex ic IIC T6 Gc
• Output: 4...20 mA, galvanically isolated
• Adjustable by PC
• Supply: 9...30 VDC
• Calibration certificate included

Temperature and standard signal transducer P30U.

• Programmable input
• Mathematical functions
• Individual channel characteristic
• 1 or 2 outputs
• Variant with internal transducer 24 VDC power supply
• RS-485 interface
• Adjustable dimension
• Data logging into internal memory (4 MB) or SD/SDHC card (4 GB)
• Transducer programming with buttons or via PC (“LPConfig” software)

• Sensor type: Pt100, Pt1000, Ni100, Ni1000, others
• Electrical connection:
  • A transmitters with output: 4…20 mA, 4...20 mA +HART, 0…10 V, RS-485 or IO-LINK
  • 2-wire, 3-wire, a contact terminal
• Measuring range: -40…80 °C
• Operating temperature: -40…80 °C
• The sensor can be distanced, meaning the TJ-O can be equipped with the following external temperature sensors: TJ-1, TJ-2, TJ-4, TJ-S
• Sensor tube:
  • Material: Stainless steel AISI304 (1.4301)
  • Diameter: Ø6 mm
  • Length: 25 mm
• Mounting box:
  • Material: Polystyrene
  • Dimentions: 64,4x 88,4x 42,2mm
  • Protection class: IP65
• The design could be changed according the requirements and drawings of the customer

• Sensor type: Pt100, Pt1000, Ni100, Ni1000, others
• Electrical connection:
  • A transmitter with output: 4…20 mA, 4...20 mA +HART, 0…10 V, RS-485 or IO-LINK
  • 2-wire, 3-wire, a contact terminal
• Measuring range: -40…180 °C (depends on probe)
• Operating temperature (case with transmitter): -40…80 °C
• The sensor TJ-1 is selected according to the individual order
• Mounting box:
  • Material: Polystyrene
  • Dimensions: 64,4x 88,4x 42,2mm
  • Protection class: IP65
• The design could be changed according the requirements and drawings of the customer

• Sensor type: Pt100, Pt1000, Ni100, Ni1000, others
• Electrical connection:
  • A transmitter with output: 4…20 mA, 4...20 mA +HART, 0…10 V, RS-485 or IO-LINK
  • 2-wire, 3-wire, a contact terminal
• Measuring range: -40…180 °C (depends on probe)
• Operating temperature (case with transmitter): -40…80 °C
• The sensor TJ-4 is selected according to the individual order
• Mounting box:
  • Material: Polystyrene
  • Dimensions: 64,4x 88,4x 42,2mm
  • Protection class: IP65
• The design could be changed according the requirements and drawings of the customer

• Sensor type: Pt100, Pt1000, Ni100, Ni1000, others
• Electrical connection:
  • A transmitter with output: 4…20 mA, 4...20 mA +HART, 0…10 V, RS-485 or IO-LINK
  • 2-wire, 3-wire, a contact terminal
• Measuring range: -40…180 °C (depends on probe)
• Operating temperature (case with transmitter): -40…80 °C
• The sensor TJ-S is selected according to the individual order
• Mounting box:
  • Material: Polystyrene
  • Dimensions: 64,4x 88,4x 42,2mm
  • Protection class: IP65
• The design could be changed according the requirements and drawings of the customer

• Operates as a temperature switch (thermostat), transducer, data logger
• Accumulated temperature data is read using a mobile phone with NFC interface
• Parametrization via NFC interface
• Display and electrical connection are independently rotatable 335°/343°
• Temperature measurement range: -50...+150 °C
• Analog output: 4...20 mA / 0...5 VDC /1...6 VDC / 0...10 VDC / switchable between mA and V
• Switch output: 2 x PNP
• Sensor: Pt1000 A
• Data logger memory: 3518 measurement points
• Measurement interval: 0,1...999,9 s
• Operating temperature: -25...+85 °C
• Supply: 15...30 VDC

• Temperature transducer TJ-DIN AV, designed to convert temperature measurement signal into 4...20 mA, 0...10 V
• Mounted on 35 mm DIN rail

• Temperature transmitter 5331A with 4...20 mA output, designed for TC, RTD, mV signal conversion to analog
• To be mounted into B-type electric head

• Temperature transmitter 5333A with 4...20 mA output, designed for RTD signal conversion to analog
• To be mounted into B-type electric head

• Temperature transmitter 5334A with 4...20 mA output, designed for TC, mV signal conversion to analog
• To be mounted into B-type electric head

• Temperature transmitter 5334B for explosive Ex atmosphere with 4...20 mA output, designed for TC, mV signal conversion to analog
• To be mounted into B-type electric head

• Temperature transmitter 5335A with 4...20 mA HART protocol output, designed for TC, RTD, mV signal conversion to analog
• To be mounted into B-type electric head

• Temperature transmitter 5350A with PROFIBUS PA communication, designed for TC, RTD, mV signal conversion
• To be mounted into B-type electric head

• Temperature transmitter 5350B for explosive Ex atmosphere with PROFIBUS PA communication, designed for TC, RTD, mV signal conversion
• To be mounted into B-type electric head

Temperature transmitter DAT1010 is designed for RTD (Pt100, Pt1000, Ni100, Ni1000, Ohm) ir voltage (mV) signal conversion to analog (4...20 mA).

The transmitter is mounted into a B-type head. Programming can be done in our company.

Temperature transmitter DAT1015 is designed for RTD (Pt100, Pt1000, Ni100, Ni1000, Ohm), thermocouple (J, K, S, R, B, E, T, N)  and voltage (mV) signal conversion to analog (4...20 mA).

The transmitter is mounted into a B-type head. Programming can be done in our company.

Temperature transmitter DAT1066 is designed for RTD (Pt100, Pt1000, Ni100, Ni1000, Ohm), thermocouple (J, K, S, R, B, E, T, N)  and voltage (mV) signal conversion to analog (4...20 mA). With galvanic isoliation (1500 VAC).

The transmitter is mounted into a B-type head. Programming can be done in our company.