Temperature measurement and control

• Temperature measurement range: -20...+60 °C
• Humidity measurement range: 0...100 %RH
• Pressure measurement range: 600...1100 hPa
• CO2 concentration measurement range: 0...5000 ppm
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 1 s...24 h
• Internal sensors
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Messages can be sent on alarms and periodically
• Data can be transferred to PC via USB-C interface
• Calibration certificate of manufacturer included
• Ambient temperature: -20...+60 °C
• Supply: 5200 mAh LiIon battery
• Protection class: IP20
• Warranty: 3 years

The P17G passive separator in a housing of 6.2 mm width and supplied from a current loop, serves to the electric isolation and filtration of the 0(4)...20 mA standard signal value without an additional supply voltage.

• The P20 programmable transducer is designed to convert temperature, resistance, voltage from a shunt and standard signals into a constant-current or constant-voltage standard signal
• The output signal is galvanicaly isolated from the input signal and supply
• The transducer is fully configurable through the PD14 programmer and free LPConfig software.

• Temperature sensor AUREGIS TJ-4 is inextricably connected to the cable. It is designed for temperature measurement from -50°C to 400°C
• Various sizes are available depending on customer requirements and drawings
• Sensor type: PT100, PT1000, K, J, Ni120, Ni1000 and others

• Sensor type: RTD (Pt100, Pt1000), TC (K, J)
• Output: RTD (Pt100, Pt1000), TC (K, J), 4...20 mA, 4...20 mA +HART, 0...10 V, RS-485, IO-LINK
• Measuring range: -30 °C ... 250 °C, 550 °C
• Accuracy: Class A or B /cl.2
• Sensor tube:
  • Material: Stainless steel AISI304 (1.4301)
  • Diameter: Ø6/8/10mm
  • Length: 100, 200, 500, 700, 1000mm or on request
• Connection head type: B
• Protection class: IP65
• Electrical connection: 2-wire, 3-wire or on request
• Process connection: G¼”; M20x1,5; G½” or on request
• Various sizes are available depending on customer requirements and drawings

• Temperature sensor AUREGIS TJ-1 is inextricably connected to the cable
• It is designed for temperature measurement from -50°C to 400°C
• Various sizes are available depending on customer requirements and drawings
• Sensor type: PT100, PT1000, K, J, PTC, NTC, Ni120, Ni1000

• The temperature sensor TJ-M is designed for measuring the temperature in the capacity ranging from -30°C to 550°C
• The design could be changed according the requirements and drawings of the customer
• Sensor type: Pt100, Pt1000, K, J
• Connection head type: M
• Protection class: IP65

• Universal air and environment quality sensor E2-CO2-series measures CO₂ (carbon dioxide) level, temperature, humidity, pressure, sound level, ambient light (LUX). Transmits instant values, average hourly values, and average 24-hour values
• Communication: wM-BUS EN13757-3/4:2013, complies OMS 4.0.2
  • Modes: C1-A/B, T1 or S1 (selectable on order)
• Measurement ranges
  • Temperature: -40…85 °C
  • Humidity: 0…100 % RH (non-condensing)
  • CO2: 0…5000 ppm (0…55 °C)
  • LUX: 0,01…83000 LUX at same frequency as the human eye
  • Absolute pressure: 20…100 kPa
  • Sound level: 20…90 dBa at 850 Hz
• Measurement accuracy
  • Temperature: ± 0,2 at +5…+60 °C; ± 0,5 at -20…+85 °C
  • Humidity: ± 2 % RH at 20…80 % RH; ± 3 % RH at 10…90 % RH; ± 3,5 % RH at 0…100 % RH
  • CO2: ± (50 ppm + 3%)
  • LUX: 4 %
  • Pressure:  0,4 kPa
• CO2 sensor calibrates every 20 days
• Warnings about low battery, CO₂ sensor malfunction, calibration not performed yet
• Transmission interval: every 90 seconds
• Measured values sample interval: every 6 minutes
• LED and sound indication about CO₂ exceeded limit
• Device has 2 antennas for maximum range in both vertical and horizontal directions
• Power supply: 2 x ER18505 3.6 V Li-SOCI2 battery pack (8200 mAh)
  • Up to 14 years battery lifetime, standard configuration and operating temperature

• Input: Pt100 (2-, 3-, 4-wire)
• Measurement range: -200...+850 °C
• Resolution: 24 bits
• Very low current consumption
• No external power supply needed
• Warranty: 3 years
• Connection: RJ-11

TSM400-1-TH is a digital temperature and humidity sensor with a 1-Wire interface. Suitable for monitoring air quality of server rooms, data centers, offices and stores.

• Temperature measurement range: -20…+60°C
  • Accuracy (min): ± 0,4 °C (in -10…+60°C range)
  • Accuracy (max): ± 0,6 °C (in -20…+60°C range)
  • Resolution: 0,1 °C
• Relative humidity measurement range: 10 to 90% (non-condensing)
  • Accuracy (min): ± 3.0 % RH (in 20…80 % RH range)
  • Accuracy (max): ± 5.0 % RH (in 10…90 % RH range)
  • Resolution: 0,1 %RH
• Excellent long-term stability
• The unique 64-Bit serial number for multi-sensors support
• Ingress protection: IP20
• Operating voltage range: 4,5…26 VDC

• Sturdy
• Hanging hook
• 3 'Y' ¼” 'MFL connectors including one with a Schrader valve

• Input: 2x thermocouples - J, K, T, N, E, B, R, and S
• Output: Modbus RTU – RS-485
• Resolution: 24 bits with DSP processing
• Working isolation voltage: 1500 Vrms
• Operating temperature / humidity: -20…+60 °C / 10…90% (non-condensing)
• DIN rail mounting
• Power supply: 5…30 Vdc
• Warranty: 3 years

TCG210-4 is a battery-powered 4G parcel temperature and humidity logger with fallback support for 2G communication. The device is compatible with HTTP/HTTPS API protocols, making it suitable for modern IoT applications. It periodically sends HTTP/HTTPS POST requests to a remote server, containing a status file in JSON format and the most recent logged data in CSV format.

• Global connectivity - Quad-band 4G LTE Cat.1 with 2G fallback ensures reliable operation worldwide.
• Battery-powered autonomy - Operates for months without external power, ideal for parcel monitoring and remote applications.
• Intelligent power management - Advanced sleep mode significantly extends battery life.
• Flexible configuration - Easy setup via Wi-Fi, SMS, or HTTP API.
• Real-time alerts - Instant SMS alarm notifications to up to five phone numbers.
• Integrated sensing - High-accuracy temperature and humidity sensor for critical parcel monitoring.
• Large data storage - Onboard memory for up to 70,000 logged records.
• Seamless IoT integration - Periodic HTTP/HTTPS POST with current status in JSON format.
• Data export - Automatic upload of logged data in CSV format to a remote server.
• Remote management - Full device control through HTTP API commands.
• Future-proof - Firmware update over Wi-Fi or 4G LTE keeps the device always up to date.
• Compact and lightweight - Designed for easy deployment in parcel logistics, cold chain transport, and warehousing.
• Safe for air transport - Powered by a compliant Li-SOCl₂ battery (IATA DGR, UN 3091, PI970 Section II), suitable for air shipment.

• Portable, small dimension temperature meter with a probe
• The probe can be 1,5 m, 3 m or of specified length
• Temperature measurement accuracy: ±1 °C
• Temperature measurement range: -50...+150 °C
• LCD screen
• 2 year warranty
• Supply: 1x6LF-22 (9 V)

• Air velocity measurement range: 0...2 / 0...10 / 0...20 m/s (selectable via jumper)
• Temperature measurement range: 0...50 °C
• Output: 0...10 V / 4...20 mA
• Option: LCD screen
• Option: relay output
• Supply: 24 VDC/VAC
• Operating temperature: 0...+50°C
• Protection class: IP54

• Temperature measurement range: -30...+80 °C
• Humidity measurement range: 0...100 %
• Output: RS-485 Modbus RTU
• Calculates absolute humidity and dew-point temperature
• Cable length: 2 m / 2 m with M8 connector / 5 m / 10 m
• Operating temperature: -20...+60 °C
• Supply: 9...28 VAC/VDC

Ambient humidity and temperature logger TERMIOPLUS-S with external sensor is designed for logging of ambient humidity and temperature in its internal memory.

• Temperature range: -30...+70°C
  • Temperature accuracy: In range -30...+70 °C: ± 0,3 °C
  • Resolution: 0.1
• Humidity range: 0...100 % RH
  • Humidity accuracy: ±2 %RH at 25 °C (30…70 %RH); ±3 %RH at 25 °C (10…90 %RH); ±4 %RH at 25 °C (0…100 %RH)
• Memory: 32000 (16000 temperature and 16000 humidity)
• USB interface for data download
• Logging interval: 15 s...10000 min
• Supply: 2xAA battery, 3.6 V
• Battery lifetime: 1 one year with 30 min. interval recording at +10 °C
• Size: 45 x 100 x 19 mm

• Ambient temperature and humidity transducer with 4...20 mA output
• Integrated sensors
• Calibration certificate is included
• Economical

• Ambient temperature and humidity transducer with 4...20 mA output
• Stem length 700 mm
• Calculated values: dew point temperature, absolute humidity, specific humidity, mixing ration, specific enthalpy
• Display with two periodically changed shown values (can be switched off)
• Integrated sensors
• Calibration certificate is included
• Programmable output
• Low temperature inertia
• For use in non-aggressive environment
• 3 year warranty

Solid drilled threaded thermowells, protective cases:

• Protect and extend the lifetime of temperature sensors and thermometers in processing applications
• Facilitate the replacement of sensors
• Allow sensor maintenance without process interruption

• Designed to be weld-in into pipelines and boilers
• Instrument standard threads (F): G1/2", G1/4"
• Dimensions according to customer's needs
• Case production: solid or welded
• Available materials: 1.4301 (AISI304), 1.4401 (AISI316), 1.4404 (AISI316L)
• Dimension tolerances according to DIN ISO 2768
• Available other materials, threads, flanges and dimensions

• Process flanges according to: EN 1092-1, DIN 2527, ASME B 16.5
• Standard instrument threads (F): G1/2", G1/4"
• Dimensions according to customer's needs
• Case production: welded or solid (flange welded)
• Available materials: 1.4301(AISI304), 1.4401 (AISI316), 1.4404 (AISI316L)
• Dimension tolerances according to DIN ISO 2768
• Available other materials, threads, flanges and dimensions

Thermowells protect and extend the lifetime of temperature sensors and thermometers in processing applications where the sensors are not mechanically or chemically compatible with the process environment. Moreover, thermowells facilitate the replacement of sensors and allow sensor maintenance without process interruption.

Carbon dioxide (CO₂) and temperature transmitter with a display CDT2000 Duct. The device is designed for measurement of air parameters in ventilation channels.

• CO₂ range 400...2000 ppm
• Temperature range 0...50 °C

• To measure carbon dioxide and temperature in air and neutral gases ranges 0…5000 ppm, 0...50 °C
• Configuration with keypad or software: measuring ranges, units, outputs settings
• Optional with display or without display
• Galvanic isolation all the ways
• On request range increase up to 0...20 000 ppm

​

Carbon dioxide (CO₂), temperature and humidity transmitter with a display CDT2000.

• Carbon dioxide (CO₂) range: 400...2000 ppm
• Humidity range: 0...100 % 
• Temperature range: 0...50 °C

• Measures carbon dioxide concentration in air, temperature, humidity
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measurement ranges: 0...2000 ppm, -30...+80 °C, 5...95 %RH
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s; CO2: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Measures carbon dioxide concentration in air, temperature, humidity
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measurement ranges: 0...10000 ppm, -30...+105 °C, 5...95 %RH
• Temperature and humidity sensor cable length: 1 / 2 / 4 m
• Carbon dioxide concentration sensor cable length: 1  2 / 5 / 10 m
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s; CO2: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

SM400-4-CPTH is a multi-sensor that supports MODBUS RTU protocol over the RS-485 interface. The sensor measures CO2 concentration, humidity, temperature and barometric pressure. Suitable for environmental quality monitoring, indoor air, smart ventilation systems, restaurants and breweries CO2 level and CO2 leakage control.

• Changeable bitrate and other communication parameters
• Non-volatile memory for all setting
• Temperature measurement range: -20 to 60°C
  • Accuracy (min): ±0.4 °C (in -10 to +60°C range)
  • Accuracy (max): ±0.6 °C (in -20 to +60°C range)
  • Resolution: 0.1 °C
• Relative humidity measurement range: 10 to 90% (non-condensing) *
  • Accuracy (min): ±3.0 %RH (in 20 to 80 %RH range)
  • Accuracy (max): ±5.0 %RH (in 10 to 90 %RH range) *
  • Resolution: 0.1 %RH
• CO2 measurements range: 400…5000 ppm
  • Accuracy: ± (40 ppm + 5 %)
  • Resolution: 1 ppm
  • Calibration: Automatic, if the sensor is exposed to fresh air for more than 30 minutes
• Pressure measurements range: 10 to 1200 hPa
  • Accuracy (min): ±1.5 (25°C, 750 hPa)
  • Accuracy (max): ±2.5 (-20°C to + 85°C, 300 to 1100 hPa)
  • Resolution: 1 hPa
• Ingress protection: IP20
• Operating voltage range: 4.5…26 VDC

• Measurement range: -40...+150 °C, -1...60 bar
• Temperature measurement accuracy: ± 1,3 °C
• Pressure measurement accuracy: ±0,5 % of full scale
• Operating temperature: -20...+50 °C
• Overload: 65 bar
• Android / iOS app for communication with the device (via Bluetooth Low Energy interface)
• 124 refrigerant gases

Temperatre, humidity and pressure meters, loggers Cxxxx, Dxxxx.
Cxxxx are designed for indication (without data logging), Dxxxx indicates and logs listed parameters.

TSH202B is a compact humidity and temperature sensor with 1-Wire interface. It is ideal for use in a variety of applications where space is limited, such as environmental monitoring systems, HVAC control, and more.

• Fully calibrated digital output
• Excellent long-term stability
• A unique 64-bit serial number for multi-sensor systems
• 3.0% relative humidity accuracy
• 12-bit resolution for humidity measurements
• 14-bit resolution for temperature measurements

• Compact thermostat for shipbuilding
• ISP version – with capillary tube, ISPT version – without capillary tube
• Measured temperature from +5...95 °C to +20...150 °C
• Switching differential: not adjustable
• Output signal: floating change-over contact
• Ambient temperature: -30...+70 °C
• Conformity: ABS, BV, CCS, DNV, GL, KRS, LRS, NKK, RINA, RMRS, EN60730-1 / EN60730-2-9: Typ 2.B.H

• Measurement range: 32…43 °C
• Measurement accuracy: ± 0,3 °C
• Measurement distance: 0…5 cm
• Measurement duration: 1 s
• Measurement location: forehead
• Automatic shut-down: 30 s
• Measurements: 149 x 38 x 42 mm
• Operating temperature: 10…40 °C
• Operating humidity: ≤ 85 %
• Certificates: ISO13485, CE, CFDA
• Supply: 2 x AAA batteries

• Input: potentiometer / 0...10 V / 4...20 mA / 3,33 mV/V / 2 mV/V / 2.5 mV/V / CANopen
• Temperature input: none / Pt100 / Pt1000 / thermocouple
• Analog output: none / 0...10 V / 0...5 V / 0,5...4,5 V / 0...20 mA / 4...20 mA
• Relay output: 3 units
• Communication interface: none / RS-232 / RS-485 / USB / CANopen
• Invertible analogue output (10...0 V, 20...0 mA)
• Fast and easy parameter configuration via USB
• Optional tare function (scaling to zero)
• Supply: 220 VAC / 24 VAC/DC
• Operating temperature: 0...50 °C
• Protection class: IP60 (front)

• To measure and data logging: carbon dioxide (0...5000 ppm), temperature (0...50 °C), atmospheric pressure (800...1100 hPa), humidity (0…100 % RH) in air and neutral gases
• Free software for configuration and data visualization
• Bluetooth communication for smartphones and tablets (Android and IOS)
• Safety lock magnetic mounting with inviolability system holder (accessories)
• Compatible with food industry environment
• Up to 4 recordable parameters simultaneously
• Optional calibration certificate

• Pressure measurement range: -250...2500 / -250...7000 Pa
• Input: 2 x  0...10 V, NTC10k, Pt1000, Ni1000, binary
• Output: Modbus RTU
• Temperature compensation in range of 0...50 °C
• Allowed overpressure: 25 kPa
• Supply: 24 VDC/VAC
• Operating temperature: -20...+50°C
• Protection class: IP54

• PID controller
• Pressure measurement range: 0...2500 Pa
• Modbus RTU communication
• Control output: 0...10 V
• External input: 0...10 V / thermistor / binary
• LCD display
• Temperature compensation
• Allowed overpressure: 25 kPa
• Supply: 24 VDC
• Operating temperature: -20...+50°C
• Protection class: IP54

• RS-485 (Modbus) protocol temperature and humidity sensor
• Temperature measurement range: -20...+60 °C
• Humidity measurement range: 5...95 %RH
• Accuracy: ±3 %RH (20...80 %RH) / ±5 %RH (5...95 %RH) / ±0,4 °C (-10...+60 °C) / ±0,6 °C (-20...+60 °C)
• Resolution: 12 bits for temperature and humidity
• Long-term stability
• Warranty: 3 years

• 1-Wire protocol temperature and humidity sensor
• Temperature measurement range: -20...+60 °C
• Humidity temperature range: 10...90 %RH
• Accuracy: ±3 %RH (20...80 %RH) / ±5 %RH (10...90 %RH) / ±0,4 °C (-10...+60 °C) / ±1 °C (-20...+60 °C)
• Resolution: 14 bits for temperature, 12 bits for humidity
• Long-term stability
• Warranty: 3 years

• 1-Wire protocol temperature and humidity sensor
• Temperature measurement range: -20...+60 °C
• Humidity temperature range: 10...90 %RH
• Accuracy: ±3 %RH (20...80 %RH) / ±5 %RH (10...90 %RH) / ±0,4 °C (-10...+60 °C) / ±1 °C (-20...+60 °C)
• Resolution: 14 bits for temperature, 12 bits for humidity
• Long-term stability
• Warranty: 3 years
• Connection: RJ-11

• RS-485 protocol temperature and humidity sensor
• Temperature measurement range: -20...+60 °C
• Humidity temperature range: 5...95 %RH
• Accuracy: ±3 %RH (20...80 %RH) / ±5 %RH (5...95 %RH) / ±0,4 °C (-10...+60 °C) / ±0,6 °C (-20...+60 °C)
• Resolution: 14 bits for temperature, 12 bits for humidity
• Long-term stability
• Warranty: 3 years
• Connection: RJ-45

• Input:
  • temperature:
    • resistance thermometers: Pt100, Pt500, Pt1000
    • thermocouples: J, K, N, E, R, S
  • resistance: 400 ohm, 4000 ohm
  • current: ± 20 mA
  • voltage: 0…10 V, -10…60 mV
• Output: relay (4), analog (1), digital RS-485/MODBUS (1),
• Three-colour display - red, green and orange, programmable in three intervals of the measured value – facilitates the observation of measured value changes.
  • digit height: 14 mm
  • highlighted measuring unit
• Four alarm outputs with signaling on LED diodes operating in six different modes.

• 1-Wire protocol temperature sensor
• Temperature measurement range: -40...+85 °C
• Accuracy: ±0,5 °C (-10...+85 °C) / ±2 °C (-40...+85 °C)
• Resolution: 12 bits
• Very low current consumption
• Warranty: 3 years
• Protection class: IP65

• 1-Wire protocol temperature sensor
• Temperature measurement range: -40...+85 °C
• Accuracy: ±0,5 °C (-10...+85 °C) / ±2 °C (-20...+85 °C)
• Resolution: 12 bits
• Very low current consumption
• Warranty: 3 years
• Connection: RJ-11

Digital thermometer SDT8 for temperature measurement from -50 to +150 °C.

• Temperature range: -30...70 °C
• Accuracy: ±0,5 °C (-10 °C...40 °C) / ± 1 °C
• Display: LCD
• Battery work time: 2 years
• Battery type: 1/2 AA (3,6 V)
• Dimensions: 45x100x19 mm
• Protection class: IP65
• Weight: 85 g
• Holder is ordered separately

Duct temperature transducer with 4...20 mA output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Calibration certificate is included.

Duct temperature transducer with 0...10 V output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Output temperature range is user adjustable. Calibration certificate is included.

• Ethernet connection
• Analog inputs: 2 (0...10 VDC)
• Digital inputs: 2
• Relay outputs: 2 (NO/NC)
• 1-Wire input (up to 8 sensors)
• Memory: 70 000 values
• Modbus TCP/IP support
• Webserver
• XML/JSON, HTTP API commands
• SNMP alarms (up to 5 recipients)
• E-mail alarms (up to 5 recipients)
• Operating temperature: -20...55 °C
• Warranty: 3 years
• Supply: 10...28 VDC