Search

• Temperature measurement range: -20...+60 °C
• Humidity measurement range: 0...100 %RH
• Pressure measurement range: 600...1100 hPa
• CO2 concentration measurement range: 0...5000 ppm
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 1 s...24 h
• Internal sensors
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Messages can be sent on alarms and periodically
• Data can be transferred to PC via USB-C interface
• Calibration certificate of manufacturer included
• Ambient temperature: -20...+60 °C
• Supply: 5200 mAh LiIon battery
• Protection class: IP20
• Warranty: 3 years

• Universal air and environment quality sensor E2-CO2-series measures CO₂ (carbon dioxide) level, temperature, humidity, pressure, sound level, ambient light (LUX). Transmits instant values, average hourly values, and average 24-hour values
• Communication: wM-BUS EN13757-3/4:2013, complies OMS 4.0.2
  • Modes: C1-A/B, T1 or S1 (selectable on order)
• Measurement ranges
  • Temperature: -40…85 °C
  • Humidity: 0…100 % RH (non-condensing)
  • CO2: 0…5000 ppm (0…55 °C)
  • LUX: 0,01…83000 LUX at same frequency as the human eye
  • Absolute pressure: 20…100 kPa
  • Sound level: 20…90 dBa at 850 Hz
• Measurement accuracy
  • Temperature: ± 0,2 at +5…+60 °C; ± 0,5 at -20…+85 °C
  • Humidity: ± 2 % RH at 20…80 % RH; ± 3 % RH at 10…90 % RH; ± 3,5 % RH at 0…100 % RH
  • CO2: ± (50 ppm + 3%)
  • LUX: 4 %
  • Pressure:  0,4 kPa
• CO2 sensor calibrates every 20 days
• Warnings about low battery, CO₂ sensor malfunction, calibration not performed yet
• Transmission interval: every 90 seconds
• Measured values sample interval: every 6 minutes
• LED and sound indication about CO₂ exceeded limit
• Device has 2 antennas for maximum range in both vertical and horizontal directions
• Power supply: 2 x ER18505 3.6 V Li-SOCI2 battery pack (8200 mAh)
  • Up to 14 years battery lifetime, standard configuration and operating temperature

• Ambient temperature and humidity transducer with 4...20 mA output
• Integrated sensors
• Calibration certificate is included
• Economical

• Ambient temperature and humidity transducer with 4...20 mA output
• Stem length 700 mm
• Calculated values: dew point temperature, absolute humidity, specific humidity, mixing ration, specific enthalpy
• Display with two periodically changed shown values (can be switched off)
• Integrated sensors
• Calibration certificate is included
• Programmable output
• Low temperature inertia
• For use in non-aggressive environment
• 3 year warranty

• Measures ambient air pressure
• Measurement range: 600...1100 hPa
• Operating temperature: -30...80 °C
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Module is designed to protect battery if it discharges below 10,5 V mark, disconnecting it from load
• Battery is automatically reconnected to load if its voltage rises
• Suitable for work with heaters, lighting, travel refrigerators, etc.
• Operating voltage: 12 V ZBxx, 24 V ZBxx-24V, 48 V ZB-48V
• Maximal current: 40 A ZB40, 80 A ZB80, 140 A ZB140
• Operating temperature: -20...50 °C
• Dimensions: 65 x 89 x 70 mm

• CO2 concentration measurement range: 0...10 000 / 50 000 ppm
• External sensor cable length 1 / 2 / 4 m
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 10 s...24 h
• Calibration certificate included
• LED, acoustic alarms
• LCD screen
• Data can be transferred to PC via USB-C interface
• Operating temperature: -20...+60 °C
• Supply: battery
• Protection class: IP54
• Warranty: 3 years

• Measures carbon dioxide concentration in air
• Measurement range: 0...2000 ppm
• Operating temperature: -30...60 °C
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Measures carbon dioxide concentration in air
• Measurement range: 0...10000 ppm
• Operating temperature: -30...80 °C
• Cable length: 1 / 2 / 5 / 10 m
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Measures carbon dioxide concentration in air
• Duct mount
• Measurement range: 0...2000 ppm
• Operating temperature: -30...60 °C
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Measures carbon dioxide concentration in air, temperature, humidity
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measurement ranges: 0...2000 ppm, -30...+80 °C, 5...95 %RH
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s; CO2: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• Measures carbon dioxide concentration in air, temperature, humidity
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measurement ranges: 0...10000 ppm, -30...+105 °C, 5...95 %RH
• Temperature and humidity sensor cable length: 1 / 2 / 4 m
• Carbon dioxide concentration sensor cable length: 1  2 / 5 / 10 m
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s; CO2: 15 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included

• CO2 concentration measurement range: 0...10 000 ppm
• Output: 4...20 mA
• Programmable
• External probe cable length: 1 / 2 / 4 m
• LCD display
• Calibration certificate included
• Ambient temperature: -30...+80 °C
• Supply: 9...30 VDC
• Protection class: IP65
• Warranty: 3 years

COMET Cloud is an Internet data storage designed for recording measured values from selected COMET measuring instruments. The data is accessible after the user's connection to the Internet and is displayed in a web browser in the form of a table or graph. Users can be notified by e-mail of all alarm conditions reported by the device. After purchasing a device that supports connection to the COMET Cloud, you can register the device in the COMET Cloud. Each user has access only to their account, which is password protected. If you run a large number of devices in the COMET Cloud, you can clearly organize them into groups and assign new users to them, who can have an overview of the group of devices. Different rights for data display and administration can be set for individual users.

Notification app for Android or iOS

• Makes available the list of sent alarm messages from COMET Cloud
• Allows instant alarming with notifications
• The application will be expanded to display measured values
• Can be installed on Android and iOS mobile device

Temperature transducers P4141, P4121, P4151, P4131, P4161, P4171, P4191 with 4...20 mA output and Pt1000 input.

P4121 – P4171 class transducers are designed to convert RTD Pt1000 (3850ppm/°C) signal to current. These transducers have 4...20 mA output. RTD sensor Pt1000 is not included.

Temperatre, humidity and pressure meters, loggers Cxxxx, Dxxxx.
Cxxxx are designed for indication (without data logging), Dxxxx indicates and logs listed parameters.

• The MQTT protocol is ideal for communication in distributed acquisition systems data (IoT applications)
• Especially suitable for server rooms, pharmaceutical and food warehouses, laboratories, museums and greenhouses
• Logged data is stored in the internal memory and then sent digitally to the user (over Ethernet)
• Alarms are formed by e-mails, on the webserver, using symbols on screen or via audible alarms
• HT20IoT can be powered by the Ethernet network (PoE – Power over Ethernet), additionally ordered
• FTP, DHCP, SMT, Modbus TCP/IP protocols

Duct temperature transducer with 4...20 mA output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Calibration certificate is included.

Duct temperature transducer with 0...10 V output is built in a durable watertight case. The length of stainless steel stem is 120 mm. Output temperature range is user adjustable. Calibration certificate is included.

• Grain temperature monitoring system for steel and concrete bins
• Digital sensors with 2-wire bus
• Sensor spacing: 2 or 3 m
• Diameter: Ø9,8 mm
• Length: 1...35 m
• Tensile strength: ≤ 2,5 t
• Operating temperature -20...50 °C
• Maximal surface temperature 85 °C
• System is ATEX-, IECEx- and GOST-R approved
• ATEX approval code: Ex II 1D Ex ia IIIC T85°C

• Grain temperature monitoring system for steel and concrete bins
• Digital sensors with 2-wire bus
• Sensor spacing: 2 or 3 m
• Diameter: Ø17 mm
• Length: 1...100 m
• Tensile strength: ≤ 8 t
• Operating temperature -20...50 °C
• Maximal surface temperature 85 °C
• System is ATEX-, IECEx- and GOST-R approved
• ATEX approval code: Ex II 1D Ex ia IIIC T85°C

• Temperature measurement range: -20...+60 °C
• Accuracy: ±0.4 °C
• Internal temperature sensor
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 1 s...24 h
• Internal sensor
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Local alarms via LED indication, on LCD screen and acoustically by built-in beeper
• Data can be transferred to PC via USB-C interface
• Calibration certificate of manufacturer included
• Ambient temperature: -20...+60 °C
• Supply: 5200 mAh LiIon battery
• Protection class: IP67
• Warranty: 3 years

• CO2 concentration measurement range: 0...5000 ppm
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: 1 s...24 h
• Internal sensor
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Messages can be sent on alarms and periodically
• Data can be transferred to PC via USB-C interface
• Calibration certificate of manufacturer included
• Ambient temperature: -20...+60 °C
• Supply: 5200 mAh LiIon battery
• Protection class: IP20
• Warranty: 3 years

• Measures temperature, humidity, calculates dew point
• Temperature measurement range: -20...+60 °C
• Humidity measurement range: 0...100 %
• Memory: up to 500,000 values in non-cyclic mode (350,000 in cyclic)
• Logging interval: 10 s...24 h
• Display and alarm refresh interval: 1 s...1 min
• Protection class: IP67
• Warranty: 3 years
• Calibration certificate of manufacturer is included (according to EN ISO/IEC 17025)
• Free analytical software COMET Vision

• Inputs: 4x external Pt1000 sensors
  • Measuring range: -200…+260 °C
  • Accuracy: ± 0.2 °C (± 0,2 %, when temperature is in range of +100...+260 °C)
  • Resolution: 0,1 °C
• Memory: up to 500,000 values in non-cyclic mode and 350 000 in cyclic mode
• Logging interval: adjustable 1 s, 10 s, 1 min
• GSM modem (GPRS)
• SMS and JSON messages can be sent via GPRS data connection
• Messages can be sent on alarms and periodically
• Data can be transferred to PC via USB-C interface
• Calibration certificate included
• Ambient temperature: -20...+60 °C
• Supply: rechargeable Li-Ion battery A8200, 3.6V/5200mAh
• Protection class: IP20
• Warranty: 3 years

• Used with grain temperature sensor cables GWSL 1100, GWSL 2100 and spear sensors GWTL-R
• Cable length up to 200 m (including the temperature cables)
• Up to 32 values of temperatures are shown in cycle
• Weight: 240 g (with batteries)
• Case material: ABS
• Supply: 2 x AA (battery life circa 1 year)
• Operating temperature: -20...+40 °C

“idOil®” is an alarm system intended for monitoring liquid levels particularly in oil and sand separators. The system consists of the idOil control unit and the idOil sensors installed in the separator. The sensor cables can be extended with a cable connector or connection box. One to three digital idOil sensors of the same or different type can be connected to the control unit. The sensors can be used to monitor the following:

• High liquid level (idOil-LIQ high liquid level sensor)
• Oil layer detection (idOil-OIL oil sensor is for class IIA explosive liquids and idOil-OIL-Soil sensor is for class IIB explosive liquids)
• Sludge layer detection (idOil-SLU sludge sensor)

“idOil®” is an alarm system intended for monitoring liquid levels particularly in oil and sand separators. The system consists of the idOil control unit and the idOil sensors installed in the separator. The sensor cables can be extended with a cable connector or connection box. One to three digital idOil sensors of the same or different type can be connected to the control unit. The sensors can be used to monitor the following:

• High liquid level (idOil-LIQ high liquid level sensor)
• Oil layer detection (idOil-OIL oil sensor is for class IIA explosive liquids and idOil-OIL-Soil sensor is for class IIB explosive liquids)
• Sludge layer detection (idOil-SLU sludge sensor)

Indoor temperature meter / transducer Txx18, designed for temperature, humidity and barometric pressure measurement.

The Wx9xx series of sensors from COMET SYSTEM enables accurate measurement of temperature, relative humidity, and atmospheric pressure, with data transmitted via the low-power LoRaWAN network. This technology allows data to be sent to a cloud storage, where users can easily view both current and historical values through a standard web browser. Each sensor has an LCD display showing the measured value and battery status.

• Possibility to connect Pt1000 sensors
• Covers up to 15 km in rural areas and 2…5 km in urban areas
• Work with Comet System LoRaWAN gateway SP041
• Battery life: from 1 to 10 years depending on transmission time and environment temperature
• Unlimited space for data in cloud
• Alarm: email and app notification
• Mobile applications for Android and iOS

• The battery or mains powered wireless M-Bus gateway B4 is highly configurable plug-and-play device used for collecting data from Wireless M-Bus meters / sensors and transmitting the data using LTE CAT-M1 and MQTT protocol
• Long range and high sensitivity internal (or external mounted) antennas
• To maximize the battery lifetime possible configuration to listen number of minutes, specific time during day, specific days and limit number of packets stored per meter / week / day / hour
• The gateway firmware can be upgraded remotely using MQTT
• B4 series gateway can be used with Lansen R4 series repeaters and transmit additional information (see datasheet)
• Configuration can be done with: Lansen Wireless M-BUS programming dongle together with our program, Lansen Configurator, other wireless M-BUS transmitters or remotely using the MQTT protocol
• Possible to activate 128 bit AES-key encryption
• Gateway suited for harsh environments, operating temperature: -30…+85 °C, protection class: IP40, IP65 and IP67
• IoT LTE M SIM card needed (acquired separately)

• Fully functional data logger
• Two-line digital LCD display
• 4 control buttons
• 32 alarm LEDs

System of data logging MS6D, MS6R (Comet System, Czech Republic). For mounting to 19" rack - one rack unit 1U. The device can be integrated into the MP033, MP034 waterproof housing. With backlight display, 4 control buttons (for configuration), 32 LED for alarm. 

• Designed for air temperature and humidity sensors / transmitters
• Transmitter entirely protected inside the shield
• Prevention of condensation by downward sensor orientation
• Advanced weather protection by maximized top cover area (Ø 250 mm)
• Passively ventilated, requires no power
• Plate system permits air flow through the sensor
• ASA plastic is resistant to mechanical damage and UV radiation. It is anti-static and very stable over time.

• Grain temperature monitoring system software for PC
• Collects data from temperature cables GWSL 1100 and GWSL 2100 and spear temperature sensors GWTL-R
• Stores, visualizes data in charts
• Alarms
• Level indication

PoE (power over Ethernet) temperature, relative air humidity, atmospheric pressure meters T4611, T3611, T7611. Only to be used with external sensors.

Application:

• Storage rooms
• Greenhouses
• Telecommunication devices
• Servers
• A/C units

PoE (power over Ethernet) temperature, relative air humidity, atmospheric pressure meters T0610, T3610, T7610. Only to be used with internal sensors.

Application:

• Storage rooms
• Greenhouses
• Telecommunication devices
• Servers
• A/C units

• Thermosetting cabinet with double doors. The cabinet dimension: 600 x 500 mm (max 2x 5,5 kW) or 800 x 600 (max 2x 7,5 kW; ... max 2x 22 kW).
• Plinth or foundation for fixing the cabinet.
• PLC controller with a display that changes the backlight depending on operating mode.
• Program saved in the controller and on the SD card, enabling transferring the program to another controller in the event of a failure.
• Router equipped with a 2G / 3G / 4G / LTE modem, 1 LAN 10 / 100 Mb/s port and radio module in the 802.11 b/g/n standard, supporting MIMO 2x2.

• Flexible spears for grain temperature measurement
• Rigid construction
• Diameter: Ø8 mm
• Penetration depth: up to 12 m
• Digital temperature sensor
• Measurements are done using PC software or handheld reader GW-200
• Temperature spears and cables can be integrated into single system

By means of three light barriers the SI-JET spray jet control systems check the density, symmetry, and cone angle of the spray jet. Choked or incorrectly set nozzles can thus be detected in time. Due to the integrated pressed air facility (at transmitter and receiver side of the fork) these systems are insensitive to dirt accumulation.

• Universal datalogger with 4 hardware MiniDIN inputs for connecting temperature and humidity probes.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 3 hardware MiniDIN inputs for connecting temperature and humidity probes and 1 for external CO2 sensor.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• External CO2 sensor, 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 inputs, 2 for voltage, current, logic and pulse signals and 2 for connecting temperature and humidity probes.
• Measures carbon dioxide (CO2) using the integrated sensor.
• Measures barometric pressure using the integrated sensor.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 inputs, 2 for voltage, current, logic and pulse signals and 2 for connecting temperature and humidity probes.
• Measures carbon dioxide (CO2) using the integrated sensor.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 inputs, 2 for voltage, current, logic and pulse signals and 2 for connecting temperature and humidity probes.
• Measures barometric pressure using the integrated sensor.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 inputs, 2 for voltage, current, logic and pulse signals and 2 for connecting temperature and humidity probes.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 hardware MiniDIN inputs, 2 for thermocouples K, J, S, B, T, N and 2 for connecting temperature and humidity probes.
• Cold junction compensation (CJC).
• Sensors of physical quantities with bipolar voltage output can also be connected. Two voltage ranges: -18...+18 mV and -60...+140 mV.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Temperature (Pt1000) and humidity probes are ordered separately. Cable length – 1, 2, 5, 10, 15 meters.
• Open collector transistor alarm output.

• Universal datalogger with 4 hardware MiniDIN inputs for thermocouples K, J, S, B, T, N.
• Cold junction compensation (CJC).
• Sensors of physical quantities with bipolar voltage output can also be connected. Two voltage ranges: -18...+18 mV and -60...+140 mV.
• Multilogger can be installed permanently to Ethernet network or work as a portable device.
• Measured values can be viewed on a web browser, as well as stored and downloaded for later analysis.
• Calibration certificate included.
• 3 rechargeable AA batteries with a power adapter, wall holder and USB cable are included in the delivery.
• Thermocouples are ordered separately.
• Open collector transistor alarm output.

• Measures ambient temperature, humidity
• Calculates dew point, absolute humidity, specific humidity, mixing ratio, specific enthalpy
• Measuring ranges: -30...+80 °C, 0...100 %RH
• Output: Ethernet
• Optional connection to WiFi network via tiny wireless router TL-WIFI
• Webserver
• Measurement interval: 2 s
• Alarm protocols: E-mail, SNMP Trap, Syslog
• Supply: 9...30 VDC
• Protection class: IP30
• Calibration certificate included